Recyclable Zr/Hf-Containing Acid-Base Bifunctional Catalysts for Hydrogen Transfer Upgrading of Biofuranics: A Review

The massive burning of a large amount of fossil energy has caused a lot of serious environmental issues (e.g., air pollution and climate change), urging people to efficiently explore and valorize sustainable alternatives. Biomass is being deemed as the only organic carbon-containing renewable resource for the production of net-zero carbon emission fuels and fine chemicals. Regarding this, the selective transformation of high-oxygen biomass feedstocks by catalytic transfer hydrogenation (CTH) is a very promising strategy to realize the carbon cycle. Among them, the important Meerwein-Ponndorf-Verley (MPV) reaction is believed to be capable of replacing the traditional hydrogenation strategy which generally requires high-pressure H₂ and precious metals, aiming to upgrade biomass into downstream biochemical products and fuels. Employing bifunctional heterogeneous catalysts with both acidic and basic sites is needed to catalyze the MPV reaction, which is the key point for domino/cascade reaction in one pot that can eliminate the relevant complicated separation/purification step. Zirconium (Zr) and hafnium (Hf), belonging to transition metals, rich in reserves, can demonstrate similar catalytic efficiency for MPV reaction as that of precious metals. This review introduced the application of recyclable heterogeneous non-noble Zr/Hf-containing catalysts with acid-base bifunctionality for CTH reaction using the safe liquid hydrogen donor. The corresponding catalysts were classified into different types including Zr/Hf-containing metal oxides, supported materials, zeolites, metal-organic frameworks, metal-organic hybrids, and their respective pros and cons were compared and discussed comprehensively. Emphasis was placed on evaluating the bifunctionality of catalytic material and the key role of the active site corresponding to the structure of the catalyst in the MPV reaction. Finally, a concise summary and prospect were also provided centering on the development and suggestion of Zr/Hf-containing acid-base bifunctional catalysts for CTH.

This review introduced the application of recyclable heterogeneous non-noble Zr/Hf-containing catalysts with acid-base bifunctionality for CTH reaction using the safe liquid hydrogen donor. The corresponding catalysts were classified into different types including Zr/Hf-containing metal oxides, supported materials, zeolites, metal organic frameworks, metal organic hybrids, and their respective pros and cons were compared and discussed comprehensively. Emphasis was placed on evaluating the bifunctionality of catalytic material and the key role of active site corresponding to the structure of the catalyst in the MPV reaction.

Introduction

The large-scale exploitation of fossil-based resources exists alongside environmental deterioration like global warming, acid rain, and air pollution (Tripathi et al., 2016; Valderrama Rios et al., 2018; Ahmad et al., 2019; Brauer et al., 2021; Schwarzman et al., 2021). On the eve of the “26th United Nations Climate Change Conference” in 2021, more than 230 major journals around the world jointly published an editorial to warn global leaders to act immediately for climate change (Atwoli et al., 2021). These serious problems compel humans to seek renewable and clean resources for the sustainable supply of fuels and chemicals (Zhang et al., 2020; Khan et al., 2021; Osman et al., 2021; Rode et al., 2021; Wu et al., 2021; Yu et al., 2021; Zantye et al., 2021; Zhang et al., 2021a). Biomass acts as the only organic carbon-containing source on earth that mainly contains carbon, hydrogen, and oxygen species (Wang et al., 2014b; Han et al., 2019; Spinelli et al., 2019; Zhu et al., 2019; Pattnaik et al., 2021). Biomass energy is ubiquitous, rich, renewable, and sustainable and its main sources are firewood, wood waste, agricultural straw, livestock manure, sugar crop waste, municipal waste with sewage, and aquatic plants, respectively (Li et al., 2018a; Luo et al., 2019; Abomohra et al., 2020; Sudarsanam et al., 2020; Wu et al., 2020). Compared with other renewable energy sources, it has unique advantages in terms of the reuse of waste resources and the production of fuels and high-value chemicals. It is highly valued in many aspects such as scientific research, politics, and the economy (Wu et al., 2018a; Mathimani and Mallick, 2019; Welch et al., 2021; Tan et al., 2022). There is a significant long-term two-way causal relationship between biomass energy consumption and economic growth (Ajmi and Inglesi-Lotz, 2020; Sabyrzhan et al., 2021). Hence, biomass has broad application potential in the future production and life of mankind (Kumar et al., 2015; Gawade et al., 2016; Hu et al., 2017; Liu et al., 2021c). However, compared to the desired products especially for fuels or fuel additives, biomass-derived feedstocks generally possess higher oxygen content (Prasomsri et al., 2013; Liao et al., 2014; Li et al., 2020a; Li et al., 2020b; Wang et al., 2020a). It is still necessary to further process the biomass feedstock to upgrade its functional groups (Dabros et al., 2018; Li et al., 2019b; Iglesias et al., 2020 Tan et al., 2021). In the field of biomass upgrading, the most widely used approach is to convert biomass (e.g., cellulose and hemicellulose) into a series of furan compounds via cascade reactions (Scheme 1) (Zhou and Zhang, 2016; Liu et al., 2019; Chen et al., 2021b). Among furan compounds, γ-valerolactone (GVL) is recognized as a kind of versatile chemical building block (Liu et al., 2021a; Kerkel et al., 2021; Delgado et al., 2022). It’s a green organic solvent and can also be used as a precursor for the manufacture of liquid fuels (Huang et al., 2018; Crabtree, 2019). 5-Hydroxymethylfurfural (HMF) has various furan rings coupled with the hydroxyl and aldehyde groups present at the exocyclic carbon atoms (Chen et al., 2018; Zhang et al., 2021b; Sarkar et al., 2021). It can be converted to levulinic acid (LA) and further produced GVL. or it can be converted to 2,5-bis(hydroxymethyl)furan (BHMF) through another route. (Kou et al., 2016; Priecel et al., 2018; Li and Jiang, 2019). Therefore, the main conversion path of this article is the production of furan compounds such as GVL and BHMF.

GRAPHIC ABSTRACT

GRAPHIC ABSTRACT

SCHEME 1

SCHEME 1. A common pathway for upgrading cellulose and hemicellulose.

Many reactions are involved in these processes, such as dehydration, hydrogenation, ring-opening (Yang et al., 2017b; Iriondo et al., 2017; Solanki and Rode, 2019). But the key speed-determining step is transfer hydrogenation via the Meerwein-Ponndorf-Verley (MPV) reduction reaction, which is also called indirect catalytic transfer hydrogenation (CTH) (Singh et al., 2015; Li et al., 2018c; Shao et al., 2021). Different kinds of alcohols can be used as H-donors in relatively mild conditions, achieving efficient catalysis performance for CTH reaction of the carbonyl group of α, β-unsaturated aldehyde/ketone (Mondelli et al., 2020). Therefore, the C=O bond is hydrogenated while retaining the C=C bond (Wu et al., 2018b; Li et al., 2018d; Jin et al., 2019; Liu et al., 2021d). Heterogeneous catalysts were wildly used in MPV reduction reactions, which can be easily recycled and also can effectively reduce industrial production costs (Santana and Krische, 2021; Pan et al., 2022). It goes without saying that the choice of materials is of great importance for the relevant catalytic system. In contrast to the indirect hydrogenation via MPV reaction using alcohol as a hydrogen donor (H-donor), there is another direct hydrogenation reaction in CTH that uses precious metals and H₂. Although precious metals (e.g., Ru, Pd, Ir, Pt) were widely studied for direct CTH, the prices were not suitable for industrialization (Tuteja et al., 2014; Brethauer and Studer, 2015; Cao et al., 2017; Wang T. et al., 2020). On the other hand, non-noble metals (e.g., Fe, Co, Cu, Ni) were restricted because of relatively low activity and/or product selectivity (Hu et al., 2019a; Zhang et al., 2019b; Shi et al., 2019; Jiang et al., 2020). These disadvantages have prompted scientists to explore alternative catalysts, which can balance economy and high selectivity (Yin and Shen, 2020). Thus, researchers discovered that transition metal carbides have similar properties with Pt metal (Pang et al., 2019). Since transition metals have both metallic and acidic properties, they can be used as effective catalysts for the upgrading of oxygen-containing compounds derived from biomass (Choi et al., 2011; Heard et al., 2016; Gonell et al., 2017; Wagner et al., 2021). It has good corrosion resistance and is not easily corroded by general acid-base aqueous solutions (Sullivan et al., 2016; Wei et al., 2021). Among the transition metals, Zr and Hf metals with similar properties have set off a wave of research craze in the field of CTH (Champness, 2011; Li et al., 2016a; B et al., 2018). Figure 1 shows that from 1995 to 2021, the number of articles published on Zr-based catalysts in 2020 is even 5 times than that of Hf-based catalysts. Although the metals of the fourth subgroup have similar properties, the research of Hf-based catalysts in this field is far from enough, which is also a trend and direction of future exploration.

FIGURE 1

FIGURE 1. Comparison of the number of publications on Zr-containing catalysts and Hf-containing catalysts. Source: web of science (a search carried out in November 2021).

There are some relevant reviews about biomass conversion and CTH reaction. For example, a comprehensive review of bifunctional catalysts to convert biomass into biofuels was proposed by Li et al. (2016a). What’s more, some reviews focused on the production of GVL from lignocellulosic biomass, (Tang et al., 2014b; Ye et al., 2020) and other studies paid attention to the mechanism and interface effects of heterogeneous CTH (Gilkey and Xu, 2016; Liu et al., 2021b). However, as far as we know, there is no review of the application of transition metal Zr/Hf catalysts used for the synthesis of biofuranics compounds. In this review, the target is to selectively discuss the latest developments of various types of Zr/Hf-containing catalysts through MPV reduction to upgrade biomass-derived feedstocks. It will focus on exploring the specific mechanism of the catalysts’ active site (Lewis/Brønsted acid and base) in each biomass upgrading reaction. Finally, some opportunities and challenges faced by CTH for efficiently converting biomass into fuels or high-value chemicals have also been prospected appropriately.

Zr/Hf-Containing Metal Oxide Catalysts

Zr has excellent high-temperature resistance, and its melting point is as high as 2,700°C. Even if it is heated to 1900°C, it will still not react with molten Al, Fe, Ni, Pt, and other metals. Commercial zirconium oxide (ZrO₂) has been used in the nuclear energy industry, national defense industry, electronic components, ceramic carbon powder, along with high-temperature resistant materials, etc. (Ishikawa et al., 2017). Among them, ZrO₂ was also used in the field of catalysis due to its excellent chemical stability and high surface chemical activity (Liu et al., 2002; Zhu et al., 2004; Gonell et al., 2017). As a typical weak acid-base bifunctional material, ZrO₂ and HfO₂ have exceptional catalytic performance in CTH reaction (Paniagua et al., 2021). In Zr/Hf-containing metal oxide catalysts, as shown in Table 1, the main researches in recent years are classified and summarized according to the reaction substrate.

TABLE 1

TABLE 1. Zr/Hf-based metal oxide catalysts.

LA and its Esters as Substrates

LA as a Substrate

LA was listed as one of the 12 high-value chemicals from biomass by the U.S. DE (Bogale et al., 2019). It was considered as a significant platform compound for the synthesis of organic chemicals (Hu et al., 2021; Tian et al., 2021). In general, there are usually two reaction pathways of heterogeneous catalysis in the production of GVL using LA and its esters [e.g., methyl levulinate (ML), ethyl levulinate (EL), butyl levulinate (BL)] as substrates. These two reaction pathways mainly depend on the controlled reaction conditions and the catalyst used during the reaction (Scheme 2) (Dutta et al., 2019). In path 1, hydrogenation reaction is prone to occur at lower temperatures to promote the conversion of LA to 4-hydroxyvaleric acid under the water phase system, which is then dehydrated to GVL under the action of a catalyst. In path 2, LA is first dehydrated to form angelica lactone at higher temperatures, which is then hydrogenated to obtain GVL. In short, hydrogen and dehydration can occur either way. But under different control reaction conditions, the sequence of these two processes will change, accordingly.

SCHEME 2

SCHEME 2. Two pathways for the conversion of LA and its esters to GVL.

Ag–Ni/ZrO₂ catalyst has attracted researchers’ attention due to its magnetic properties that are easy to separate (Hengne et al., 2014). The two metals play a synergistic effect in the transformation of LA and furfuryl alcohol (FA) (1:1) mixture to GVL. It also proved that Ag–Ni/ZrO₂ has a comprehensive scope of applications in the one-pot CTH of biomass-derived C3 to C6 molecules, with relatively high conversion and selectivity (>80%) (entry 1 of Table 1). In addition to using high-purity synthetic chemicals as substrates, researchers were further required to explore some methods that can be closer to biomass raw materials to produce GVL. Tang et al. developed an in-situ catalyst generation system to produce GVL (Tang et al., 2015). The system can decompose the HCl/ZrO(OH)₂ catalyst in LA and 2-butanol (2-BuOH) solution autonomously and then a 2-BuOH in-situ H-donor was employed to catalyze the cyclization of LA esterification to GVL. The highlight of this system was that crude LA can be directly used to produce GVL. The crude LA was extracted from the acid hydrolysis of cellulose (47.8% yield), and flowed into 2-BuOH. Finally, 2-BuOH was used to extract LA and FA from the cellulose hydrolysate (90.2% v. s. 15.1%), as depicted in entry 2 of Table 1. Even in the presence of humin after use, a GVL yield of 82.0% can be successfully obtained. In addition, when investigating the influence of solvent, it was found that the GVL yield of 2-BuOH was much lower than that of 2-Propanol (2-PrOH) (27.5% vs. 62%) at 200°C because the steric effect of 2-BuOH was stronger than 2-PrOH. Continue to increase the temperature to 240°C, the steric effect of 2-BuOH can be overcome, and the yield can be increased to 84.5%. According to Derjaguin–Landau–Verwey–Overbeek (DLVO) theory, the principle of the catalysts agglomeration phenomenon was speculated. That was, the absorbed LA and H-donors enhanced the electrostatic repulsion between the ZrO(OH)₂ particles formed in situ, thereby preventing further agglomeration in 2-BuOH. In other words, the dispersibility and morphology of ZrO(OH)₂ particles that played a key catalytic role mainly depended on the solvent and the substrate. Most Cu-ZrO₂ catalysts were prepared by co-precipitation with mixed precursors (entry 3 of Table 1) (Hengne and Rode, 2012). Its excellent catalytic performance should be attributed to its strong surface acidity. The effective active component in the catalytic hydrogenation process was the reduced Cu particles dispersed on the catalyst surface. The introduction of Cu into the tetragonal ZrO₂ lattice can enhance the adhesion of these particles as well as make them dispersed. It can also enhance the number of acid sites, among which Lewis acid was also determined to enhance the transfer hydrogenation activity. Changing the starting material from LA to ML and the H-donor from water to methanol, Cu-ZrO₂ still had a very objective activity (entry 4 of Table 1).

ML as a Substrate

Ni/ZrO₂ was also used to convert ML and LA to GVL, which were catalyzed and reacted to test the active materials (Sakakibara et al., 2019). It was concluded that the Ni contributed to the hydrogenation of ML and LA, and the Zr contributed to the lactonization of the hydrogenated product. Under relatively mild conditions of 90°C, the GVL yield reached 92% (entry 5 of Table 1). But the disadvantage was that the reaction time was as long as 20 h. It is well known that GVL can be directly hydrogen transfer catalyzed by ZrOCO₃. Further studies by Ma et al. found that using ZrOCO₃ as a carrier, the introduction of Cu/Cu⁺ can increase the CTH activity (entry 6 of Table 1) (Ma et al., 2020). And Cu/ZrOCO₃ can also further convert GVL into 1,4-Pentanediol (1,4-PDO) through the MPV reaction. This may be caused by the coordination effect between the Cu and the acid-base sites of the carrier. Cu vacancy (Cu⁰) and Cu ion (Cu⁺) were formed after in-situ reduction. Cu⁺ can be used as Lewis acid to adsorb and activate the C=O group through the electron lone oxygen atom pair. Alcohol can be excited to become an activated metal hydride on the Cu⁰ surface, and then attack the activated C=O group to form an O-H group. ZrOCO₃ was an amphoteric catalyst, which can also promote the MPV reaction through six-membered ring intermediates. In addition, amphoteric carriers (such as Al(OH)₃ and ZrOCO₃) contained more acid-base sites than basic carriers (such as Mg₂(OH)₂CO₃ and ferric hydroxide), demonstrating a better catalytic activity accordingly.

EL as a Substrate

EL was used to prepare GVL through CTH. Tang et al. used ZrO(OH)₂ xH₂O catalyst to obtain 89.1% EL conversion and 75.3% GVL yield in ethanol (EtOH) under 240°C for 1 h (entry 7 of Table 1) (Tang et al., 2014a). First, EtOH was adsorbed on the surface of the catalyst and dissociated into the corresponding alkoxide. EL obtained two hydrogen atoms from EtOH to obtain the intermediate ethyl 4-hydroxypentanoate (4-HPE). Then 4-HPE underwent intramolecular transesterification to obtain the final product GVL. But there was another reaction path, 4-HPE and EtOH were etherified to produce by-product 4-ethoxypentanoate (4-EPE). Self-aldol condensation may occur between EL, GVL, and aldehyde dehydrogenated from EtOH, and the formation of trace by-products can be ignored in the system. Doping boric acid in Zr-containing catalysts can increase its acid content, but the traditional wet impregnation method was difficult to control the leaching of the boron component during the reaction. Therefore, He et al. used the sol-gel method to improve the synthesis of the mesoporous Zr/boron mixed oxides catalyst (He et al., 2016a). ZrOCl₂ 8H₂O and boric acid were stirred at 40°C for 3 h and then transferred to an oven to evaporate the solvent for 4 h after sonication. After drying at 80°C for 1 day, it was calcined at 450°C for 6 h. In general, the preparation process was relatively simple. With this amorphous material catalyst, 95.1% EL conversion and 88.5% GVL yield were obtained at 200°C for 4 h (entry 8 of Table 1). As the boron content increased, the surface area, acid density, and alkali density of the mesoporous material improved correspondingly. Nonetheless, adding too much boron to ZrO₂ will reduce the alkali density and inhibit the alkalinity of the catalyst. However, ZrO₂ catalyst still existed the disadvantage of high temperature or long time during the reaction (entry 9 of Table 1) (Tang et al., 2013). To address this issue, Al-Zr mixed metal catalysts were prepared by the co-precipitation method (He et al., 2016b). ZrOCl₂ 8H₂O and Al(NO₃)₃ 9H₂O were dissolved in deionized water, and then an aqueous ammonia solution (25–28%) was added dropwise. Next, the solution underwent a series of methods such as pH adjustment, aging, drying, and calcination to obtain the target solid catalyst. It was found that when Al was added to ZrO₂, the surface area was enlarged and the number of effective acid and base sites of the catalyst was increased. With 2-PrOH as the H-donor and solvent, the EL conversion was 95.5% and the GVL yield was 83.2% at 220°C (entry 11 of Table 1). Both formic acid and LA can be obtained from sugars in an equimolar ratio were found by Li et al. Therefore, if FA is used as an H-donor and LA is used as a substrate to synthesize GVL, it is obviously a reasonable system. Nano-FeZrO_X materials have also been reported to have magnetic recyclable properties. The acid-base bifunctional catalysts of superparamagnetism were synthesized through the reaction of solvent heat treatment and hydrolysis condensation. Upon using EtOH as H-donor, effective conversion of EL to GVL was successfully conducted. A series of FeZrO_x catalysts with different Fe-Zr ratios were prepared (entry 11 of Table 1) (Li et al., 2015). It was found that ZrFeO (1:3)-300 with Fe₃O₄ covered by a ZrO₂ layer had an appropriate distribution of acid-base sites as well as a medium surface area and pore size. The yield of GVL can be reached as high as 87.2% (3 h, 230°C). In addition, the catalyst containing Zr and Fe can also be combined with the solid acid HY2.6 to directly convert sugar into GVL, with a yield of 44.7%. To be specific, Ni(NO₃)₂ 6H₂O and ZrOCl₂ 8H₂O were used to synthesize magnetic Ni-Zr nanocatalysts for the conversion of various biomass derivatives (Li et al., 2016b). This hydrogen-reduced magnetic Zr₅Ni₅ nanoparticles (<20 nm) catalyzed EL to produce GVL (95.2% yield) within 3 h at 200°C (entry 12 in Table 1). Surprisingly, the system can also catalyze the conversion of fructose, glucose, cellobiose, and carboxymethyl cellulose into GVL and EL in one pot, with a total yeild of 69.5, 60.1, 56.0, and 51.5%, respectively. And ICP-OES detected that only 0.3 wt% Ni and 0.5% Zr were immersed in 2-PrOH. The very small amount of immersion can clearly explain the heterogeneity of the catalyst and the nature of easy recycling. In addition, the nano-catalyst was combined with the solid acid HY6, the catalyst was easily attracted by the permanent magnet because of its magnetic properties. The used catalyst was washed 3 times with EtOH and dried, and it can be reused more than 5 times. In addition, the catalyst can be recovered by more than 89–93%, which is very suitable from an economic and convenient point of view.

Also using EL as a substrate, Yang et al. developed a microsphere Ti/Zr porous oxide catalyst through a sol-gel process combined with solvent heat treatment (Yang et al., 2017a). With hexadecyl amine (HDA) as the directing agent, the catalysts (TixZry) with different Ti/Zr molar ratios that have −Zr−O−O−Zr− network were developed. This not only allowed the mixed oxide to have adjustable porosity and large surface area but also enhanced its acidity and alkalinity. Compared to the amorphous structure of commercial titanium oxide (TiO₂) and ZrO₂, Ti/Zr oxides were spherical. Experiments and tests showed that Ti₂Zr₈ had the largest surface area (385 m²/g), appropriate acidity (1.12 mmol/g), and alkalinity (0.46 mmol/g), which was the best option. In general, if there was a base in the reaction system, the reaction activity will be improved. The increase in reactivity benefited from the ability to accept hydroxyl protons from the H-donor. There were also many sources of bases, which can be organic ligands, solvent molecules, or dissolved alkaline substances. The catalyst can be reused at least 6 times, and it can still obtain almost complete EL conversion and GVL yield of greater than 84.4% (entry 13 of Table 1). BL was also one of the common LA and its esters (entry 14 of Table 1) (Chia and Dumesic, 2011).

FF (Furfural) as a Substrate

For the conversion of FF to FA, the hollow core-shell magnetic catalyst named Zr(OH)₄@CoFe₂O₄, was developed and employed for CTH (entry 15 of Table 1) (Hou et al., 2021). Firstly, 2-PrOH was adsorbed on the surface of Zr(OH)₄ and interacted with Lewis acid sites (Zr⁴⁺) and base sites (O^2-) to form metal alkoxide. Then, the O atom on the carbonyl group of FF was activated by Zr⁴⁺. A typical six-membered ring transition state was formed. Then hydride transfer from alkoxide to the carbonyl group of FF was accomplished. Finally, the newly formed FA was desorbed from the surface of the catalyst along with acetone, and the active site of Zr⁴⁺ was re-exposed for the next run.

One-pot conversion of FF to GVL can use commercial HfCl₄ as a catalyst (Li et al., 2021b). With 2-PrOH as H-donor, the yield of GVL reached 65.5% in 8 h at 180°C (entry 16 of Table 1). During the reaction, HfCl₄ is hydrolyzed in situ to produce HfO(OH)₂ xH₂O (medium Lewis basic) and HCl (strong Brønsted acid). Together with the Lewis acid site (Hf⁴⁺), they play a synergistic effect in the cascade reaction process, which is significantly improved the catalytic activity. HfCl₄ provides Lewis acid site (Hf⁴⁺), while HfO(OH)₂·xH₂O and HCl were gradually in situ generated by the HfCl₄ hydrolysis in 2-PrOH due to the presence of residual water to provide Lewis base site (O^2-) and Brønsted acid site (HCl), respectively. 1) The carbonyl group of FF was adsorbed on the Lewis acid site (Hf⁴⁺), and 2-PrOH with the oxygen and hydrogen atom of the hydroxyl group were respectively adsorbed to the Lewis acidic Hf⁴⁺ and the Lewis basic oxo-ion site. Then, a six-membered ring transition state was formed to complete the transfer hydrogenation process. FF was converted to Furfuryl Alcohol (FA), at the same time the 2-PrOH was transformed to acetone. 2) FA reacting with 2-PrOH was catalyzed by Lewis acid sites to form isopropyl furfuryl ether (FE) by etherification reaction. 3) The conversion of IPL to isopropyl 4-hydroxyvalerate (4-HPE) via transfer hydrogenation was similar to that of FF to FA, which was also catalyzed by the Lewis acid-base site (Hf⁴⁺-O^2-). 4) 4-HPE undergone cyclization reaction to produce equivalent GVL was conducted in the presence of acid sites. In addition, the recycled catalysts can effectively catalyze the conversion of FF to FA after being calcined (2-PrOH as H-donor and the yield is 60.5% at 170°C for 1.5 h).

HMF as a Substrate

CTH mechanism of HMF on ZrO(OH)₂ was shown in Scheme 3 (Hao et al., 2016). The carbonyl oxygen of HMF coordinated with the alkoxide a to form a six-membered ring transition state b on Zr species. The hydride was transferred from the alkoxide to the carbonyl of HMF in b. Meanwhile, the new carbonyl (aldehyde) dissociated and released the intermediate c. Then another EtOH coordinated with it to form d. At the end, the newly reduced carbonyl (BHMF) dissociated to regenerate the alkoxide a. The BHMF yield of 88.9% can be achieved by reacting for 2.5 h at 150°C (entry 17 of Table 1).

SCHEME 3

SCHEME 3. The mechanism for the CTH of HMF into BHMF over ZrO(OH)₂ (Hao et al., 2016).

The mechanism by which Zr-containing metal oxides catalyze the completion of transfer hydrogenation of carbonyl compounds via MPV reduction reaction is shown in Scheme 4. First, the alcohol is absorbed by the Lewis acid sites in the catalyst to form the corresponding alkoxide (Gonell et al., 2017). Then, the carbonyl group combines with the alkoxide to produce a six-membered ring transition state (Injongkol et al., 2017). Finally, a coordinated hydrogen transfer occurs between the activated carbonyl compound and the alkoxide. process. At the same time, the obtained new carbonyl chemical substance ketone is released. Finally, another alcohol molecule participates in the reaction to generate the target product and the starting alkoxide.

SCHEME 4

SCHEME 4. General reaction mechanism of hydrated ZrO₂.

Zr/Hf-Containing Supported Material Catalysts

The carrier material usually uses mesoporous molecular sieves, which generally have relatively large specific surface areas, large pore sizes, along with regular pore structures (Taniya et al., 2010). Mesoporous molecular sieves are regarded as good shape-selective catalysts and have better catalytic activity and selectivity than zeolite molecular sieves when organic macromolecular substances participate (Shen et al., 2014). In addition, the pore size can be continuously adjusted in the range of 2–50 nm, and the pores and the large and silan-rich surface (up to 2000 m²/g) are easy to modify (Gao et al., 2021a). Mesoporous molecular sieves are often used as carriers to load or dope transition metal (e.g., Zr and Hf) elements and rare earth elements into their frameworks, surfaces, or pores. There is no doubt that mesoporous materials have also shown their talents in the field of biomass catalytic upgrading (Table 2).

TABLE 2

TABLE 2. Zr/Hf-containing supported material catalysts.

LA and its Esters as Substrates

Using LA as a reaction substrate, ZrO₂ was supported on typical hexagonal mesoporous Si, such as Mobil Composition of Matter-41 (MCM-41) and Santa Barbara Amorphous-15 (SBA-15) (entry 1, 2, 4 in Table 2) prepared by Kuwahara et al. (2014). The silicon carrier itself is inactive, and the reaction kinetics demonstrated that the pore size of mesoporous Si had little effect on the catalytic activity. However, it was possible to increase the CTH reaction activity by expanding the surface area of the oxide support carrier, which can change the local structure of the Zr species. Specifically, the high surface area of Si support provided a surface environment that was suitable for the introduction of highly dispersed low-coordination Zr. The loss of used catalytic activity was due to the strong adsorption of organic residues on the catalyst surface. This prevented the next batch of organic substrates from entering the Zr active site. Similar catalysts have also been reported, and the conversion and yield have been further improved (entry 3 of Table 2) (Kuwahara et al., 2017). For the conversion of EL to GVL, using biopolymer chitosan as a support to prepare the efficient Zr-containing catalyst (chitosan–Zr) was developed by Wang et al. (2020c). Chitosan is derived from the diacylation of chitin (Synowiecki and Al-Khateeb, 2003). The world’s marine ecosystems produce about 1,600 million tons of chitin each year (Aydın and Aksoy, 2009). And it was the second kind of abundant biopolymer in nature after cellulose, but they were underutilized. Many–NH2 and–OH groups exist in the chitosan, which means it has a strong chelating ability for M⁺. The conversion rate of the relevant catalysts containing Zr or Hf can reach 100%, and the corresponding yield was 97% (entries 5 and 6 of Table 2). Undoubtedly, it was a wise strategy to use biomass-derived chemicals to prepare catalysts for the efficient valorization of biomass feedstocks.

FF as a Substrate

Using FF as the starting substrate, the same material had been studied with different Zr coatings of ZrO₂ using wet chemical methods (entry 7 of Table 2) (Iglesias et al., 2018). The first type was related to the strong acid position on the interface with Si. Another type of highly dispersed t-ZrO₂ crystals that were ubiquitous in the second and third layers was related to the position of the weak acid. This catalyst was used for the cascade reaction of FF to GVL. In addition, pyridine titration experiments during vacuum and 2-PrOH soaking were also carried out, proving that the Lewis acidity of all ZrO₂ monolayer thicknesses dominated the key role. A single ZrO₂ monolayer had a few Brønsted acid sites. And this may be related to residual surface silanol. The etherification and isomerization of FA to EL reduced the reaction rate. Fe₃O₄/ZrO₂@MCM-41 was tailored by the impregnation of ZrO₂ on mesoporous MCM-41 support coated by Fe₃O₄. It could efficiently catalyze the cascade reaction in terms of conversion of FF to GVL (entry 8 of Table 2) (Gao et al., 2021). The introduction of these two substances did not change the original ordered hexagonal framework of MCM-41. The incorporation of Fe₃O₄ was a simple way to adjust its acidity. The kinetic study demonstrated higher activation energy for the LA-to-GVL step (86.9 kJ/mol) than that of FF transfer hydrogenation (35.0 kJ/mol) and that of subsequent alcoholysis process (51.0 kJ/mol). The catalyst could be fully recovered and reused because of its excellent magnetic property. By Zr K-edge XAFS analysis, it can be seen that the Zr⁴⁺ oxide species anchored on the silica surface in a low-coordination state played the most important role in the reaction. Another application of this catalyst was the conversion of FF and 2-methylfuran (2-MF) to diesel precursors through the hydroxyalkylation/alkylation (HAA) reaction (Luo et al., 2018). The mesoporous catalyst was prepared by using ZrO₂ and phosphotungstic acid (TPA) on the inside and outside of the pores of SBA-15 (Srinivasa Rao et al., 2018) (entry 9 of Table 2). It has also been reported that Zr-SBA-15 performs average in transforming FF to FA (Iglesias et al., 2015). However, it has excellent performance when reducing cyclic ketones with secondary alcohols. After the reaction, the corresponding alcohol yield was as high as 99% (entry 10 of Table 2).

Zr/Hf-Containing Zeolite Catalysts

Zeolite is a kind of nanoporous aluminosilicate crystal (Chai et al., 2021; Mardiana et al., 2022). Because of its regular pore structure and adjustable acidity, it is widely used in adsorption, separation, and catalysis (Sushkevich et al., 2014; Koreniuk et al., 2015; Wang et al., 2016c; Kim et al., 2020). The support material mainly uses mesoporous molecular sieves, which are used to provide templates to increase the stability and surface area of the catalyst, while zeolite will coordinate with the metal and form new bonds. As we all know, the catalytic activity of a molecular sieve is closely related to its unique acidity (Ramanathan et al., 2008; Melero et al., 2018; Cho et al., 2020). Usually, the acidity of zeolite is mostly affected by the isostructural substitution of Al³⁺ by Si⁴⁺ in the framework. This can create an imbalance of negative charges in the crystal lattice, and the concomitant exchangeable cations can make up for this imbalance (such as H⁺, Na⁺, K⁺). When protons are connected to oxygen atoms that are connected to silicon and Al atoms, the local charge transfer weakens and lengthens the O-H bond. In turn, this enhances the strength of its Brønsted acidity (Melero et al., 2017). The final result of these bonding interactions is that the local environment determines the type and intensity distribution of acidic sites. After a long-term research, scientists have found that if the concentration of substituted tetrahedral atoms does not exceed a certain threshold, Brønsted acid sites can show a constant acid strength which is suitable for adsorption and catalysis (Hernández et al., 2016). Therefore, the high intrinsic catalytic activity of zeolite is mainly derived from the excellent stability of the transition state in the nanopore confinement. Table 3 compares the catalytic effects of several different Zr/Hf-containing zeolite catalysts with the substrate as the classification standard.

TABLE 3

TABLE 3. Zr/Hf-containing zeolite catalysts.

LA and its Esters as Substrates

The reaction system of converting LA to GVL can use Zr-Beta and MFI topological structure nano-layer aluminosilicate (Al-MFI-ns) as the bicatalyst (entry 1 of Table 3) (Bui et al., 2013). Both of these steps resulted in the oxidation of the H-donor, which can be separated from the product. And it can be regenerated under mild gas-phase conditions and was directly put into use next time. It was noteworthy that this process can be achieved with cheap catalysts (e.g., Ni or Cu). Moreover, the combined catalysts can also convert hemicellulose to GVL. This also provides a new potential process for the transformation of pentoses to GVL.

The process of reducing ML to GVL by Lewis acid catalyst based on relevant kinetic parameters was described Luo et al. (2014). The reaction sequence and the rate of the mechanism were calculated. And the kinetic parameters of Ti, Sn, Zr, and Hf β-catalysts at different temperatures were analyzed (entry 2 of Table 3). Although the selectivity of GVL was over 94%, the turnover rate of these three zeolite catalysts was different during the MPV reaction process, and the Hf β catalyst had the highest activity. It is confirmed that the stronger the Lewis acid of the catalyst is, the more stable the six-membered ring transition state of the rate-limiting CTH step can be achieved (Assary et al., 2013). Kinetic studies were carried out by changing the H-donor (primary alcohol and secondary alcohol), proving that reducing the chain length of the alcohol did not affect the Ea.

EL was catalytically reduced to GVL by Zr-Beta zeolite. A small amount of Zr (Si/Zr ∼75–200) was incorporated into the zeolite (Wang et al. (2014a). The Zr-Beta zeolite catalyst with isolated Zr atoms with Lewis acidity was prepared (entry 3 of Table 3). Density functional theory (DFT) calculation studies showed that Zr⁴⁺ was located in unique crystallographic positions of zeolite. To test its industrialization potential, the catalyst effect was further tested in the batch reactors and continuous flow reactors. Through the investigation of the mechanism, it was found that Brønsted acid sites can cause other side reactions. For example, the production of hemiacetals, pentenes, and their isomers reduced the selectivity to GVL.

FF as a Substrate

TUD-1 mixed with Zr/Al and zeolite β-type silicate catalyst was prepared and used for a series of conversion of FF (entry 4 and 5 of Table 3) (Antunes et al., 2016). Using 2-BuOH as an H-donor, a stepwise kinetic modeling study was successfully carried out. The effection of catalysts materials on intermediates selectivity was revealed. It was found that the Zr site played a decisive role in the reduction of FF to FA and levulinate (LE) to GVL. It was proved that the coexistence of Al sites can promote the acid catalysis step, involving the process of FA to alkyl furfuryl ethers (FEs), LEs, angelica lactones (AnLs), and LA, respectively. A similar combination also used the catalysts of Zr-HY (Lewis acid) and Al-HY (Brønsted acid) (Zhang et al. (2019a). The Zr-containing zeolite is prepared by a post-synthesis method (entry 6 of Table 3). Zr was added after the dealumination of the parent Al-containing zeolite. However, the model shown in Figure 2 exhibits that there is a certain dimensional limitation in the coordination of FF and 2-PrOH at the Zr Lewis acidic site in the pore channel. Besides, active sites of Zr-Al-Beta zeolites can be changed by mild alkaline treatment (e.g., LiOH, NaOH, KOH) (Gao et al., 2020). It is worth mentioning that alkaline treatment can improve recalcitrance to deactivation and coking, which is beneficial for the recycling of the catalyst.

FIGURE 2

FIGURE 2. The model of the spatial limitation of the coordination of the catalyst and the substrate in the pore channel [copyright from Zhang et al. (2019a)].

For the CTH conversion of FF to FA. 2-PrOH as the H-donor over cation-exchanged Lewis acidic BEA zeolite was calculated by DFT (Prasertsab et al., 2018). The catalytic activity of tetravalent metal centers (Sn, Zr, and Hf) substituted into BEA. It found that in the order Zr ≥ Hf > Sn, based on Ea.

In short, the binding capacity of the Hf-zeolite molecular sieve was better than that of the Zr-zeolite molecular sieve. This is because the activation energy of the Zr-zeolite reaction was lower when the Hf-zeolite molecular sieve catalyzed the reaction (Injongkol et al., 2017). The Zr-zeolite catalyst played an important role in the combination of stone and Zr/Hf to form the Lewis acid center, which was believed to constitute the active site of the catalyst. Moreover, it was further determined that this would play an important role in the adsorption and activation of the reactants. The Lewis acid site combined with the carbonyl group to activate the unsaturated C=O double bond, and finally formed the alcohol compound product.

Zr/Hf-Containing Metal-Organic Framework Catalysts

The term MOF was introduced in 1995 and was now widely accepted (Furukawa et al., 2013). It was a kind of coordination polymer material with good crystal form (Wang et al., 2016a; Goetjen et al., 2020). MOF catalysts have been developed successfully in the application of renewable energy and environmental fields, which have good design capabilities (Zhang et al., 2017; Lin et al., 2021; Mautschke and Llabres, 2021). Highly adjustable porosity and specific surface area, high density of accessible metal sites were the fascinating part of this material (Rui et al., 2021). The microporous zeolite material has diffusion limitations. But the MOF has a mesopore with a diameter of about 9.8 nm, facilitating the full diffusion and mixing of the various substances in the reaction. In terms of BET surface area, zeolite is about 200–500 m² g⁻¹, while MOF is about 1,000–10000 m² g⁻¹ (Dhakshinamoorthy et al., 2011). Generally, the surface area and porosity of MOF were much higher than those of zeolite, but the chemical and thermal stability of MOFs are not as good as that of zeolite. Zr/Hf-containing MOFs catalysts can be seen everywhere in the field of the transfer hydrogenation of biomass-based carbonyl compounds. Table 4 summarizes the reaction conditions and yields of some excellent Zr/Hf-containing MOF catalysts for the conversion of biomass-based chemicals.

TABLE 4

TABLE 4. Zr/Hf-containing MOF catalysts.

LA and its Esters as Substrates

For the reaction of LA to GVL, Yun et al. avoided most of the toxic solvent dimethylformamide (DMF) which were typically used in the preparation of Zr polysulfide catalysts (Yun et al., 2019). Instead, they prepared the catalyst ZrF with fumaric acid and ZrCl₄ in water. In particular, they also used monocarboxylic acids as regulators, which affected the formation and morphology of aquatic zirconia, but did not affect its crystal structure and acidity. ZrF was adjusted with formic acid, acetic acid, and propionic acid, obtaining F-ZrF, A-ZrF, and P-ZrF, respectively. As a comparison, W-ZrF synthesized directly in water without a regulator and D-ZrF prepared in DMF in a traditional mode were also established. The order of particle size is F-ZrF (270 nm) >A-ZrF (130 nm) >P-ZrF (55 nm) >D-ZrF (25 nm). The size of ZrF was related to the molecular weight of the monocarboxylic acid. A regulator with a relatively low molecular weight can obtain ZrF with larger particle size and less excessive aggregation, which is beneficial for catalysis. W-ZrF without modifier did not have a good granular shape but existed in the form of a large block. Among them, at 200°C in 2 h, ZrF prepared by formic acid showed a 98% conversion of LA and 96% yield of GVL (entry 1 of Table 4).

HPW@MOF-808 was fabricated via a facile impregnation method with H₃PW₁₂O₄₀ and Zr-based MOF (Li et al., 2021a). Although MOF-808 had good activity in CTH reaction, its Brønsted acidity did not meet the requirements. Therefore, adding HPW (strong Brønsted acid) can effectively promote the esterification of LA with 2-PrOH and the subsequent lactonization reaction. Besides, MOF-808 had high acid resistance, which can exist stably in HCl and its cavity was large enough to encapsulate HPW. The yield of GVL can be obtained by reacting at 160°C for 6 h (entry 2 of Table 4)., and the yield can be increased by 5% when the temperature was increased by 20°C. The dipping method for HPW@MOF-808 was relatively simple, but the preparation of MOF-808 was nearly a week, the process was complicated and time-consuming.

Expanding the starting material from LA to its ester, MOF material catalyst (e.g., sulfonic acid-functionalized UiO-66) also performed well (entry 3 of Table 4) (Kuwahara et al., 2016). UiO-66(Zr) is comprised of 12-coordinated Zr₆O₄(OH)₄ clusters connected with 1,4-benzene dicarboxylate (BDC) linkers (Hu et al., 2016). Due to the very strong force between Zr-O, UiO-66(Zr) material has good water and thermal stability, and the structure can be maintained stably for a long time in a solution of pH = 1–11 (Shearer et al., 2014). Observing Scheme 5, it can be seen that each Zr-O cluster is 12-fold connected to adjacent clusters through a benzene dicarboxylate linker, and stacked together (Kuwahara et al., 2016). Correspondingly, it was confirmed that by FT-IR analysis, the Zr-O cluster only coordinated with the carboxylic acid oxygen atom, but not the sulfonated oxygen atom. With the increased degree of substitution of the sulfonic acid ligand, the XRD intensity and N₂ adsorption capacity of the microporous solid decreased significantly. In other words, the crystallinity and surface area of MOF materials decreased with the increase of sulfonic acid ligands, defects or irregular connections, and catalyst activity increased. Lewis basic sites (Zr₆O₄(OH)₄ cluster) catalyzed the CTH reaction of LA and its esters (entry 3 of Table 4). Brønsted-acid site (-SO₃H) promoted continuous intramolecular dealcoholization. The acid-base sites were arranged adjacent to each other in the confined nanospace, and had a synergistic effect on the entire reaction.

SCHEME 5

SCHEME 5. Possible reaction mechanism for CTH process of levulinate esters to produce GVL over UiO-66-S_x catalyst and its structure diagram [Copyright from Kuwahara et al. (2016)].

A variety of Zr-containing MOFs with different ligands were prepared for the conversion of EL to GVL (Valekar et al., 2016). UiO-66(Zr) showed good catalytic activity (92.7% GVL yield) at a high temperature (200°C), as shown in entry 4 of Table 4. In contrast, MOF-808 has been shown to produce GVL (85% yield) quickly at a moderate reaction temperature (130°C). It is worth mentioning that the latter also performed well in open systems using solvent reflux. In addition, through acid-base modification of the BDC ligand, the changes in its structure and catalytic effect were studied. It was found that the -COOH functional group can provide additional acidity, but the surface area and pore volume of the material have a considerable loss, and the presence of the -NH₂ group in the ligand provided additional alkalinity to the material, and the surface area loss was small. This was due to the smaller size of the -NH₂ group compared to the -COOH group. The order of pore size and EL conversion and GVL yield showed consistency, that was UiO-66(Zr)-COOH (25% EL conversion, 13.9% GVL yield) < UiO-66(Zr)-NH₂ (99% EL conversion, 64.6% IPL yield) < UiO-66(Zr) (100% EL conversion, 92.7% GVL yield). The low catalytic efficiency of UiO-66 (Zr)-COOH was because EL only reacted on its surface or diffused slowly into its narrow pores. On the contrary, when UiO-66(Zr)-NH₂ was used, almost all EL was converted, but the main by-product IPL was produced. This proved that UiO-66(Zr) functionalized with -NH₂ will preferentially undergo transesterification with excess 2-PrOH. Similar conversion and yield have been obtained in other work using the same substrate (entry 4 of Table 4) (Rojas-Buzo et al., 2018).

Using EL as the starting substrate, it can be directly converted to GVL through transfer hydrogenation. Sergio et al. prepared a series of materials such as UiO-66 and MOF-808, using formic acid as a modulator (Rojas-Buzo et al., 2018). The latter can be converted into GVL to obtain 100% FF conversion and 97% yield (2 h, 100°C), as shown in entry 5 of Table 4. Compared to UiO-66 (pore size 6Å), MOF-808 has a wider pore structure (pore size 14 Å), which allows the conversion of larger substrates (Mautschke and Llabres, 2021). In the cascade reaction, the combination of Hf-MOF-808 with Al-Beta catalyst was used, and a 51% yield was obtained after 6 h of reaction (entry 5 of Table 4). Hf-MOF-808 showed excellent activity and specific selectivity in hydrogenating carbonyl compounds through the CTH strategy because of its poor crystallinity, defects, large specific surface, and abundant Lewis acid-base sites. By using DFT calculations on the mechanism of MPV reaction, Lin et al. found that carbonyl compounds (e.g., ketones and alcohols) filled the defects of Hf-MOF (Lin et al., 2021). Lewis acid with Hf as the center can coordinate with the oxygen of the substrate molecule, and form a six-membered ring transition state. But other reactive groups with insufficient hardness or large steric hindrance (e.g., -NO₂, C=C, -CN) were difficult to coordinate with Hf, which was difficult to play a catalytic role. This also explained why Hf-MOF materials have specific selectivity for reducing carbonyl groups.

FF as a Substrate

For the reaction of FF to GVL, DUT-67 (Hf) performed well. All Hf⁴⁺ contained in the Hf₆O₈ cluster of 12-linked UiO-66(Hf) was saturated, so it is difficult to introduce SO₄^2- through a post-synthetic modification method (Li et al., 2019c). In contrast, each Hf cluster of DUT-67 (Hf) is 8 times connected to the 2,5-thiophenedicarboxylic acid (H₂TDC) linker (Bon et al., 2013). An inorganic acid (H₂SO₄) can be added to introduce Brønsted acid sites. The optimal ratio of sulfated DUT-67(Hf) can convert 100% of FF and undergo a cascade reaction (180°C for 20 h) to finally obtain 84.9% GVL (entry 6 of Table 4). However, the preparation process of the catalyst was very complicated and time-consuming, which was a challenge for the promotion of large-scale use.

In the classic reaction of FF to FA under mild conditions, three Zr-molybdenum compounds (UiO-66, UiO-67, and DUT-52) with the same ligand-metal node coordination but different porous properties were compared. It was proved that the metal node connectivity was more important than high porosity when the Zr-porous membrane material underwent a CTH reaction (Valekar et al., 2020). In addition, the synthesis of an M-MOF-808 material has also been optimized, which can also obtain a 94.2% FF conversion and 90% FA yield after reacting at 40°C for 24 h (entry 7 of Table 4). Low-temperature conditions provided novel ideas for new applications of low-grade waste heat. P/Zr-MOF catalysts were prepared by (NH₄)₂HPO₄ pyrolysis approach starting from Zr-MOFs (Wang Y. et al., 2020). P/Zr-MOFs compared with Zr-MOFs, a part of O–Zr–O in the MOFs was phosphated to form O–Zr–P and P–Zr–P, in which Zr–P possessed stronger Lewis acidity and basicity than those of Zr–O. The increase of reaction temperature and time was conducive to the CTH of FF. However, too high a reaction temperature will result in a decrease in the conversion of FF. Meanwhile, too long reaction time will lead to side reactions of excessive hydrogenation and hydrogenolysis, resulting in a decrease in the selectivity of FA (entry 8 of Table 4).

In a word, Zr/Hf-containing MOFs exhibited good chemical, thermal, and mechanical stability due to the strong bond between Zr/Hf and oxygen and their high coordination number. Scheme 6 clearly shows the proposed structure of MOFs built from 12-connected and 6-connected Zr₆/Hf₆ clusters coordinated with ditopic and tritopic carboxylate linkers, respectively (Nguyen et al., 2019).

SCHEME 6

SCHEME 6. (A). Zr₆/Hf₆ cluster. UiO-type MOF structures of (B) Zr/Hf-UiO-66 and (C) Zr-, Hf-UiO-67. Interpenetrated structure (D) of VNU-1(Zr) and VNU-2(Hf). (E) Structures of MOF-808 (Zr) and VNU-11(Hf). Color code: C, black; O, red; Zr or Hf, blue; cages, yellow and purple [Copyright from Nguyen et al. (2019)].

Zr/Hf-Containing Metal-Organic Hydride Catalysts

Metal-organic hydride materials have also been known as unconventional MOF (UMOF) (Gagnon et al., 2012; Goetjen et al., 2020). Compared with the MOF material with good crystal form, Metal-organic hydrides are polymer with an amorphous structure but have good stability and more accessible sites. The organometallic coordination polymerization catalyst has high catalytic activity and good molecular tailoring (Wang et al., 2016b; Liu et al., 2021e). By adjusting the microstructure of catalysts, such as the substituents of the ligand, the coordination atom, and the electronic and three-dimensional environment of the coordination center, the molecular design and assembly of the polymer can be realized at the molecular level (Erickson et al., 2015; Hu et al., 2018; Liu et al., 2019; Peng et al., 2021). In this way, the physical properties of polymers can be controlled, and various polymers with novel functions and stereoisomers can be obtained (Asghari and Yoshida, 2006; Dutta et al., 2012; Jain et al., 2015; Zhou et al., 2019a). Table 5 summarizes the reaction conditions and yields of some excellent Zr/Hf-containing metal-organic hydride catalysts for the conversion of biomass-based chemicals.

TABLE 5

TABLE 5. Zr/Hf-containing metal-organic hydride catalysts.

LA and its Esters as Substrates

Using LA as a substrate, a new type of organic zirconium borate (Zr-BDB) was developed by Song et al. to convert it to GVL (Song et al., 2021). 1,4-Benzodiboric acid (BDB) and ZrOCl₂.8H₂O were synthesized by a solvothermal method in DMF (entry 1 of Table 5). As a Lewis acid, BDB can coordinate with and activate the hydroxyl group in alcohol. At the same time, Zr was combined to activate the carbon group, achieving the purpose of synergistically catalyzing the MPV reaction. The yields of different substrates (ML > EL > BL) to GVL were due to the increased steric hindrance from methyl to butyl.

In the system of EL to GVL, there were many different catalysts, such as Zr-BDB, PPOA-Hf, HA-Zr, Zr-SRf, Zr-PhyA, Hf-ATMP, Zr–CA, 2,5-furandicarboxylic acid (FDCA)-Hf, Zr-TMPA, Zr-HBA, Hf-OFR, Hf-GO, Hf-DTMP (entry 4–17 of Table 5). All of them were coordinated by different organic ligands. Hf-OFR was prepared by the oxytetracycline fermentation broth residue (OFR), which is an abundant solid waste in the fermentation industry (Chen et al., 2021a). It is beneficial for both pharmaceutical wastes and bio-based resources. Hazardous and tricky to treat. EL was completely converted to obtain GVL with a yield of 85% (160°C, 6 h) by PPOA-Hf catalyst (Wu et al., 2018b). Ea was estimated at approximately 53 kJ/mol, which was relatively lower than other catalysts. The layered metal phosphonate-phosphate hybrid can be used for ion exchange. Using humic acid (HAs) as a raw material to synthesize Zr-containing catalyst (Zr-HA) was proposed (Xiao et al., 2017). HAs are an important part of lignite (typical low-rank coal) with abundant reserves. This low-rank coal is usually only used as a low-quality fuel. If it can be applied to fine chemical catalysts, it will be a new method to realize the classification and clean utilization of coal. Similarly, HA and the solid residues (SR) after HA extraction from lignite were used to prepare Zr-SRf catalyst (Zhang et al., 2018). Compared to the previous study, this work had greatly shortened the reaction time (7 h V.S. 24 h) and improved the selectivity (83% V.S. 99.5%). Besides, graphene oxide (GO) is rich in acidic carboxyl groups and phenolic hydroxyl groups (Palermo et al., 2016; Karthik et al., 2021). Through the coordination of Hf⁴⁺/Zr⁴⁺ with the carboxyl group in graphene oxide, Hf-GO, and Zr-GO catalysts were constructed (Li et al., 2020c).

There are not many studies on BL as the substrate, and zirconium phosphates were used in this reaction (Li et al., 2017). The BL conversion at 2 h was 98.1%, and the GVL yield was 95.7% (entry 19 of Table 5). Compared with ZrO₂, the binding energies of Zr3d and O1s of all ZrPO-X materials were significantly increased. This was due to the introduction of phosphorus, leading to the decrease of Zr electron density and the increase of surface hydroxyl groups.

FF as a Substrate

For the conversion of FF to FA, a template-free method to synthesize various heterogeneous acid−base bifunctional nitrogen-containing alkyltriphosphonate-metal hybrids (MPN) catalysts were synthesized by Li et al. (Li et al., 2016c). The organotriphosphate-zirconium hybrid (ZrPN) mainly focused on the CTH reactions of biomass-derived carbonyl compounds to alcohols and aldoses to ketoses (entry 20 of Table 5). Through calculation, the rate constant of ZrPN at 100°C was 3.6 × 10⁻³s⁻¹, which was 12 times than that of ZrO₂. The Ea of ZrPN and ZrO₂ were 70.5 and 79.1 kJ/mol, respectively. Both two proved the superior performance of the Zr N-Alkyltriphosphate nanohybrid from the perspective of reaction kinetics. It’s worth paying high attention that the intramolecular CTH of C3−C6 aldoses to the corresponding ketoses in water was also studied. Generally, Al-zeolites can not catalyze glucose isomerization due to the weakening of Lewis acid sites existing in water. In contrast, Lewis acid sites in ZrPN can not be hampered by water, which showed excellent potential in CTH reaction. In another word, ZrPN can be extrapolated to other similar lignocellulose-derived substrates for upgrading biomass.

The conversion of FF can also be achieved by simply assembling lignosulfonate and ZrCl₄ to form a Zr-containing polyphenol biopolymer catalyst under hydrothermal conditions (entry 22 of Table 5) (Zhou et al., 2019b). Lignosulfonate has a sulfonic acid group and can be used as an alkali-free acidic site. Therefore, dangerous sulfonation can be avoided. Catalytic experiments were also carried out with 18 typical aldehydes and ketones in the traditional chemical industry as substrates. It proved that Lignosulfonate-based catalysts had good universality and application potential. Different proportions of phenylphosphonic acid (PhP) and Hf were used to prepare the acid-base bifunctional nano-hybrid catalyst PhP-Hf, which can convert FF to FA (entry 23 of Table 5) (Li et al., 2019a). The catalyst had a moderate acid-base site and acidity. PhP-Hf was weaker than that of HfO₂, but it also promoted the reaction. Acid (Hf⁴⁺) and base (O^2-) sites had a synergistic effect on the CTH reaction of FF to FA. The base sites facilitated the adsorption and dissociation of 2-PrOH on the catalyst, and the aldehyde group was activated by Hf⁴⁺. Then the six-membered ring transition state was formed in situ and completed the hydrogen transfer. And the Ea was calculated at about 60.8 kJ/mol.

The Hf-TA catalyst was synthesized in DMF with naturally occurring tannic acid (TA) as a ligand to coordinate with HfCl₄. (Wang et al., 2020d). The advantage of this method was that renewable and natural resources were used to construct an efficient and environmentally friendly Hf-containing catalyst, and the preparation process was simple. Although the general catalyst can only be recycled about 5 times, the catalytic effectiveness of the 10th used catalyst was better than the first time. It was further confirmed by FT-IR spectra, showing that the residual DMF in the pore structure of the catalyst was gradually replaced by 2-PrOH during the reuse process. This would facilitate contact with more active sites, increasing the MPV activity. Under the relatively mild reaction conditions (70°C, 3 h), a high yield of 99.0% of FA can be obtained (entry 25 of Table 5). Zirconium phosphonate The materials synthesized by the coordination of organic acids and zirconium were widely used in the biomass-based conversion. Zr-containing catalysts such as Zr-HAs, Zr-DTMP, HPW/Zr-β (entries 24, 26, 27 of Table 5) also can be used in similar systems from FF to FA or GVL. By regulating the ratio of organic phosphonate and inorganic phosphate with the center of Zr metal (Silbernagel et al., 2016), further optimization of the MPV reduction reaction system could be successfully carried out. The specific active sites required for each step of FF to GVL were shown in Scheme 7. Lewis acid/base sites were responsible for the MPV reduction (FF to FA, and EL to GVL), while Brønsted acid sites exhibited key effects on the etherification reaction (FA to FE) and ring-opening reaction (FE to EL).

SCHEME 7

SCHEME 7. Mechanism of FF to GVL over PhP-Hf.

HMF as a Substrate

Converting HMF to BHMF is also a significant path for biomass-derived conversion. A new Hf-based metal-organic coordination polymer (Hf-DTMP) was assembled by HfCl₄ and diethylene triaminepenta (methylene phosphonic acid) (DTMP) (Hu et al., 2019b). The mechanism was that 2-BuOH, and HMF were first adsorbed on catalyst. Subsequently, 2-BuOH was dissociated into the active H and alkoxide by O^2-. Meanwhile, the carbonyl group of HMF was activated by Hf⁴⁺. Then, a six-membered intermediate was generated by the dissociated alcohol and carbonyl group with Hf⁴⁺-O^2-. Finally, BHMF was eventually formed via CTH (entry 28 of Table 5). In contrast, the magnetic catalysts (MZCCP) synthesized by ZrCl₄, cyanuric acid (CA), and Fe₃O₄ did not have an advantage in terms of yield (90% V.S. 64.2%) (entry 29 of Table 5) (Hu et al., 2018).

Conclusion and Perspectives

Mountains of researches proved that CTH is a significant strategy to transform biomass-based substrates into chemical platform products and fuel precursors of high value. Zr/Hf can be supported on other materials or coordinated/coupled with them to form Zr/Hf-containing materials, of which they can play a significant role in CTH that is similar to noble metal catalysis. In this review, the catalytic effects and mechanisms of different types of Zr/Hf-containing catalysts are discussed. Various kinds of materials demonstrate different properties and preparation methods. Zr/Hf-containing oxides are relatively inexpensive and easily available. However, their basic sites are not strong and are easily affected by solvents, and the corresponding reaction activity is not ideal. Supported catalysts containing Zr/Hf can use existing templates to enhance stability and increase surface area. The zeolite catalysts are prone to be affected by the hydroxyl groups on Si, and the acidic enhancement of Lewis can effectively fix the metal and coordinate. The MOF catalysts generally have a good crystal form and spatial structure. However, the preparation process of these three catalysts is complicated and the relevant precursors are expensive, which is not suitable to apply from an economic point of view. Relatively speaking, the preparation steps of metal-organic hybrid materials are simpler and the time is shorter, which have abundant sources and room for expansion.

To establish a mature industrialization system, economic benefits and environmental impacts should be taken into account. In other words, the preparation and reaction process of the catalyst should be as simple and time-saving as possible. Also, the consumption of raw materials and energy should be low. Correspondingly, the purity and quality of the obtained product should be high. The problem at this stage is that there are seasonal differences in the availability of biomass raw materials, and the competitiveness of economic benefits is not very strong. As the saying goes, there is no useless waste, only misplaced resources. How to convert this huge amount of useless waste into resources that can replace the heavily polluting traditional energy and generate economic benefits is a problem that needs to be tackled on the road to green development. And this depends on the joint efforts of scientific researchers, enterprises, and the government, respectively. We still need to propose a new solid acid catalyst design strategy. 1) Using non-precious metal materials and green solvents to achieve a win-win situation for the economy and environmental protection. 2) Increasing the density of acid and base sites accessible to the catalyst. 3) Controlling the ratio of Lewis/Brønsted acid sites. 4) Developing more functional group synergistic catalysis. 5) Modulating the wettability of the catalyst surface together with increasing its water resistance. 6) Simplifying the catalyst preparation process, reducing the preparation cost, and controlling the energy consumption of each link accurately.

Author Contributions

Writing—original draft preparation, YL Revising—manuscript, XL Figure drawing, ML Writing—reviewing, YM Data curation, JL Editing, ZZ Writing—reviewing, supervision, HZ All authors have read and agreed to the published version of the manuscript.

Funding

The authors appreciate the financial support from the National Natural Science Foundation of China (21908033), Fok Ying-Tong Education Foundation (161030), Natural Science Special Foundation of Guizhou University ((2021)16 Special Post B), and GZU (Guizhou University) Found for Cultivation ((2020)73).

Conflict of Interest

The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest.

Publisher’s Note

All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article, or claim that may be made by its manufacturer, is not guaranteed or endorsed by the publisher.

References

Abomohra, A. E.-F., Elsayed, M., Esakkimuthu, S., El-Sheekh, M., and Hanelt, D. (2020). Potential of Fat, Oil and Grease (Fog) for Biodiesel Production: A Critical Review on the Recent Progress and Future Perspectives. Prog. Energ. Combustion Sci. 81, 100868. doi:10.1016/j.pecs.2020.100868

CrossRef Full Text | Google Scholar

Ahmad, S. F. K., Md Ali, U. F., and Isa, K. M. (2019). Compilation of Liquefaction and Pyrolysis Method Used for Bio-Oil Production from Various Biomass: A Review. Environ. Eng. Res. 25, 18–28. doi:10.4491/eer.2018.419

CrossRef Full Text | Google Scholar

Ajmi, A. N., and Inglesi-Lotz, R. (2020). Biomass Energy Consumption and Economic Growth Nexus in OECD Countries: A Panel Analysis. Renew. Energ. 162, 1649–1654. doi:10.1016/j.renene.2020.10.002

CrossRef Full Text | Google Scholar

Antunes, M. M., Lima, S., Neves, P., Magalhães, A. L., Fazio, E., Neri, F., et al. (2016). Integrated Reduction and Acid-Catalysed Conversion of Furfural in Alcohol Medium Using Zr,Al-Containing Ordered Micro/mesoporous Silicates. Appl. Catal. B: Environ. 182, 485–503. doi:10.1016/j.apcatb.2015.09.053

CrossRef Full Text | Google Scholar

Asghari, F. S., and Yoshida, H. (2006). Dehydration of Fructose to 5-hydroxymethylfurfural in Sub-critical Water over Heterogeneous Zirconium Phosphate Catalysts. Carbohydr. Res. 341, 2379–2387. doi:10.1016/j.carres.2006.06.025

PubMed Abstract | CrossRef Full Text | Google Scholar

Assary, R. S., Curtiss, L. A., and Dumesic, J. A. (2013). Exploring Meerwein-Ponndorf-Verley Reduction Chemistry for Biomass Catalysis Using a First-Principles Approach. ACS Catal. 3, 2694–2704. doi:10.1021/cs400479m

CrossRef Full Text | Google Scholar

Atwoli, L., Baqui, A. H., Benfield, T., Bosurgi, R., Godlee, F., Hancocks, S., et al. (2021). Call for Emergency Action to Limit Global Temperature Increases, Restore Biodiversity, and Protect Health. Med. J. Aust. 215, 210–212. doi:10.5694/mja2.51221

CrossRef Full Text | Google Scholar

Aydın, Y. A., and Aksoy, N. D. (2009). Adsorption of Chromium on Chitosan: Optimization, Kinetics and Thermodynamics. Chem. Eng. J. 151, 188–194. doi:10.1016/j.cej.2009.02.010

CrossRef Full Text | Google Scholar

Bogale, T. F., Gul, I., Wang, L., Deng, J., Chen, Y., Majerić-Elenkov, M., et al. (2019). Biodegradation of 1,2,3-trichloropropane to Valuable (S)-2,3-dcp Using a One-Pot Reaction System. Catalysts 10, 3. doi:10.3390/catal10010003

CrossRef Full Text | Google Scholar

Bon, V., Senkovska, I., Baburin, I. A., and Kaskel, S. (2013). Zr- and Hf-Based Metal-Organic Frameworks: Tracking Down the Polymorphism. Cryst. Growth Des. 13, 1231–1237. doi:10.1021/cg301691d

CrossRef Full Text | Google Scholar

Brauer, M., Casadei, B., Harrington, R. A., Kovacs, R., Sliwa, K., Davaakhuu, N., et al. 2021). Taking a Stand against Air Pollution - the Impact on Cardiovascular Disease. Eur. Heart J. 42, 1460–1463. doi:10.1093/eurheartj/ehaa1025

PubMed Abstract | CrossRef Full Text | Google Scholar

Brethauer, S., and Studer, M. H. (2015). Biochemical Conversion Processes of Lignocellulosic Biomass to Fuels and Chemicals - a Review. Chimia 69, 572–581. doi:10.2533/chimia.2015.572

PubMed Abstract | CrossRef Full Text | Google Scholar

Bui, L., Luo, H., Gunther, W. R., and Román-Leshkov, Y. (2013). Domino Reaction Catalyzed by Zeolites with Brønsted and Lewis Acid Sites for the Production of γ-Valerolactone from Furfural. Angew. Chem. Int. Ed. 52, 8022–8025. doi:10.1002/anie.201302575

CrossRef Full Text | Google Scholar

Cao, W., Luo, W., Ge, H., Su, Y., Wang, A., and Zhang, T. (2017). UiO-66 Derived Ru/ZrO2@C as a Highly Stable Catalyst for Hydrogenation of Levulinic Acid to γ-valerolactone. Green. Chem. 19, 2201–2211. doi:10.1039/c7gc00512a

CrossRef Full Text | Google Scholar

Chai, Y., Dai, W., Wu, G., Guan, N., and Li, L. (2021). Confinement in a Zeolite and Zeolite Catalysis. Acc. Chem. Res. 54, 2894–2904. doi:10.1021/acs.accounts.1c00274

PubMed Abstract | CrossRef Full Text | Google Scholar

Champness, N. R. (2011). The Future of Metal-Organic Frameworks. Dalton Trans. 40, 10311–10315. doi:10.1039/c1dt11184a

PubMed Abstract | CrossRef Full Text | Google Scholar

Chen, S., Wojcieszak, R., Dumeignil, F., Marceau, E., and Royer, S. (2018). How Catalysts and Experimental Conditions Determine the Selective Hydroconversion of Furfural and 5-hydroxymethylfurfural. Chem. Rev. 118, 11023–11117. doi:10.1021/acs.chemrev.8b00134

PubMed Abstract | CrossRef Full Text | Google Scholar

Chen, Y., Yao, X., Wang, X., Zhang, X., Zhou, H., He, R., et al. (2021). Direct Use of the Solid Waste from Oxytetracycline Fermentation Broth to Construct Hf-Containing Catalysts for Meerwein-Ponndorf-Verley Reactions. RSC Adv. 11, 13970–13979. doi:10.1039/d1ra01738a

CrossRef Full Text | Google Scholar

Chen, Y., Zhang, L., Yang, Y., Pang, B., Xu, W., Duan, G., et al. (2021). Recent Progress on Nanocellulose Aerogels: Preparation, Modification, Composite Fabrication, Applications. Adv. Mater. 33, 2005569. doi:10.1002/adma.202005569

CrossRef Full Text | Google Scholar

Chia, M., and Dumesic, J. A. (2011). Liquid-phase Catalytic Transfer Hydrogenation and Cyclization of Levulinic Acid and its Esters to γ-valerolactone over Metal Oxide Catalysts. Chem. Commun. 47, 12233–12235. doi:10.1039/c1cc14748j

CrossRef Full Text | Google Scholar

Cho, H. J., Kim, D., and Xu, B. (2020). Selectivity Control in Tandem Catalytic Furfural Upgrading on Zeolite-Encapsulated Pt Nanoparticles through Site and Solvent Engineering. ACS Catal. 10, 4770–4779. doi:10.1021/acscatal.0c00472

CrossRef Full Text | Google Scholar

Choi, J. H., Mao, Y., and Chang, J. P. (2011). Development of Hafnium Based High-K Materials-A Review. Mater. Sci. Eng. R: Rep. 72, 97–136. doi:10.1016/j.mser.2010.12.001

CrossRef Full Text | Google Scholar

Crabtree, R. H. (2019). Transfer Hydrogenation with Glycerol as H-Donor: Catalyst Activation, Deactivation and Homogeneity. ACS Sustain. Chem. Eng. 7, 15845–15853. doi:10.1021/acssuschemeng.9b00228

CrossRef Full Text | Google Scholar

Dabros, T. M. H., Stummann, M. Z., Høj, M., Jensen, P. A., Grunwaldt, J.-D., Gabrielsen, J., et al. (2018). Transportation Fuels from Biomass Fast Pyrolysis, Catalytic Hydrodeoxygenation, and Catalytic Fast Hydropyrolysis. Prog. Energ. Combustion Sci. 68, 268–309. doi:10.1016/j.pecs.2018.05.002

CrossRef Full Text | Google Scholar

Delgado, J., Vasquez Salcedo, W. N., Bronzetti, G., Casson Moreno, V., Mignot, M., Legros, J., et al. (2022). Kinetic Model Assessment for the Synthesis of γ-valerolactone from N-Butyl Levulinate and Levulinic Acid Hydrogenation over the Synergy Effect of Dual Catalysts Ru/C and Amberlite IR-120. Chem. Eng. J. 430, 133053. doi:10.1016/j.cej.2021.133053

CrossRef Full Text | Google Scholar

Dhakshinamoorthy, A., Alvaro, M., Corma, A., and Garcia, H. (2011). Delineating Similarities and Dissimilarities in the Use of Metal Organic Frameworks and Zeolites as Heterogeneous Catalysts for Organic Reactions. Dalton Trans. 40, 6344–6360. doi:10.1039/c1dt10354g

PubMed Abstract | CrossRef Full Text | Google Scholar

Dutta, A., Patra, A. K., Dutta, S., Saha, B., and Bhaumik, A. (2012). Hierarchically Porous Titanium Phosphate Nanoparticles: An Efficient Solid Acid Catalyst for Microwave Assisted Conversion of Biomass and Carbohydrates into 5-hydroxymethylfurfural. J. Mater. Chem. 22, 14094. doi:10.1039/c2jm30623a

CrossRef Full Text | Google Scholar

Dutta, S., Yu, I. K. M., Tsang, D. C. W., Ng, Y. H., Ok, Y. S., Sherwood, J., et al. (2019). Green Synthesis of Gamma-Valerolactone (Gvl) through Hydrogenation of Biomass-Derived Levulinic Acid Using Non-noble Metal Catalysts: A Critical Review. Chem. Eng. J. 372, 992–1006. doi:10.1016/j.cej.2019.04.199

CrossRef Full Text | Google Scholar

Erickson, K. A., Stelmach, J. P. W., Mucha, N. T., and Waterman, R. (2015). Zirconium-catalyzed Amine Borane Dehydrocoupling and Transfer Hydrogenation. Organometallics 34, 4693–4699. doi:10.1021/acs.organomet.5b00415

CrossRef Full Text | Google Scholar

Furukawa, H., Cordova, K. E., O’Keeffe, M., and Yaghi, O. M. (2013). The Chemistry and Applications of Metal-Organic Frameworks. Science 341, 1230444. doi:10.1126/science.1230444

PubMed Abstract | CrossRef Full Text | Google Scholar

Gagnon, K. J., Perry, H. P., and Clearfield, A. (2012). Conventional and Unconventional Metal-Organic Frameworks Based on Phosphonate Ligands: Mofs and Umofs. Chem. Rev. 112, 1034–1054. doi:10.1021/cr2002257

PubMed Abstract | CrossRef Full Text | Google Scholar

Gao, G., Jiang, Z., and Hu, C. (2021). Selective Hydrogenation of the Carbonyls in Furfural and 5-hydroxymethylfurfural Catalyzed by Ptni alloy Supported on SBA-15 in Aqueous Solution under Mild Conditions. Front. Chem. 9, 759512. doi:10.3389/fchem.2021.759512

PubMed Abstract | CrossRef Full Text | Google Scholar

Gao, L., Li, G., Sheng, Z., Tang, Y., and Zhang, Y. (2020). Alkali-metal-ions Promoted Zr-Al-Beta Zeolite with High Selectivity and Resistance to Coking in the Conversion of Furfural toward Furfural Alcohol. J. Catal. 389, 623–630. doi:10.1016/j.jcat.2020.07.002

CrossRef Full Text | Google Scholar

Gao, X., Yu, X., Peng, L., He, L., and Zhang, J. (2021). Magnetic Fe3O4 Nanoparticles and ZrO2-Doped Mesoporous MCM-41 as a Monolithic Multifunctional Catalyst for γ-valerolactone Production Directly from Furfural. Fuel 300, 120996. doi:10.1016/j.fuel.2021.120996

CrossRef Full Text | Google Scholar

Gawade, A. B., Tiwari, M. S., and Yadav, G. D. (2016). Biobased Green Process: Selective Hydrogenation of 5-Hydroxymethylfurfural to 2,5-Dimethyl Furan under Mild Conditions Using Pd-Cs2.5H0.5PW12O40/K-10 Clay. ACS Sustain. Chem. Eng. 4, 4113–4123. doi:10.1021/acssuschemeng.6b00426

CrossRef Full Text | Google Scholar

Gilkey, M. J., and Xu, B. (2016). Heterogeneous Catalytic Transfer Hydrogenation as an Effective Pathway in Biomass Upgrading. ACS Catal. 6, 1420–1436. doi:10.1021/acscatal.5b02171

CrossRef Full Text | Google Scholar

Goetjen, T. A., Liu, J., Wu, Y., Sui, J., Zhang, X., Hupp, J. T., et al. (2020). Metal-organic Framework (Mof) Materials as Polymerization Catalysts: A Review and Recent Advances. Chem. Commun. 56, 10409–10418. doi:10.1039/d0cc03790g

CrossRef Full Text | Google Scholar

Gonell, F., Boronat, M., and Corma, A. (2017). Structure-reactivity Relationship in Isolated Zr Sites Present in Zr-Zeolite and ZrO2 for the Meerwein-Ponndorf-Verley Reaction. Catal. Sci. Technol. 7, 2865–2873. doi:10.1039/c7cy00567a

CrossRef Full Text | Google Scholar

Han, X., Guo, Y., Liu, X., Xia, Q., and Wang, Y. (2019). Catalytic Conversion of Lignocellulosic Biomass into Hydrocarbons: A Mini Review. Catal. Today 319, 2–13. doi:10.1016/j.cattod.2018.05.013

CrossRef Full Text | Google Scholar

Hao, W., Li, W., Tang, X., Zeng, X., Sun, Y., Liu, S., et al. (2016). Catalytic Transfer Hydrogenation of Biomass-Derived 5-hydroxymethyl Furfural to the Building Block 2,5-bishydroxymethyl Furan. Green. Chem. 18, 1080–1088. doi:10.1039/c5gc01221j

CrossRef Full Text | Google Scholar

He, J., Li, H., Liu, Y., Zhao, W., Yang, T., Xue, W., et al. (2016a). Catalytic Transfer Hydrogenation of Ethyl Levulinate into γ -valerolactone over Mesoporous Zr/B Mixed Oxides. J. Ind. Eng. Chem. 43, 133–141. doi:10.1016/j.jiec.2016.07.059

CrossRef Full Text | Google Scholar

He, J., Li, H., Lu, Y.-M., Liu, Y.-X., Wu, Z.-B., Hu, D.-Y., et al. (2016b). Cascade Catalytic Transfer Hydrogenation-Cyclization of Ethyl Levulinate to γ-valerolactone with Al-Zr Mixed Oxides. Appl. Catal. A: Gen. 510, 11–19. doi:10.1016/j.apcata.2015.10.049

CrossRef Full Text | Google Scholar

Heard, C. J., Hu, C., Skoglundh, M., Creaser, D., and Grönbeck, H. (2016). Kinetic Regimes in Ethylene Hydrogenation over Transition-Metal Surfaces. ACS Catal. 6, 3277–3286. doi:10.1021/acscatal.5b02708

CrossRef Full Text | Google Scholar

Hengne, A. M., Malawadkar, A. V., Biradar, N. S., and Rode, C. V. (2014). Surface Synergism of an Ag-Ni/ZrO2 Nanocomposite for the Catalytic Transfer Hydrogenation of Bio-Derived Platform Molecules. RSC Adv. 4, 9730–9736. doi:10.1039/c3ra46495d

CrossRef Full Text | Google Scholar

Hengne, A. M., and Rode, C. V. (2012). Cu-ZrO2 Nanocomposite Catalyst for Selective Hydrogenation of Levulinic Acid and its Ester to γ-valerolactone. Green. Chem.. 14, 1064–1072. doi:10.1039/c2gc16558a

CrossRef Full Text | Google Scholar

Hernández, B., Iglesias, J., Morales, G., Paniagua, M., López-Aguado, C., García Fierro, J. L., et al. (2016). One-pot cascade Transformation of Xylose into γ-valerolactone (GVL) over Bifunctional Brønsted-Lewis Zr-Al-Beta Zeolite. Green. Chem. 18, 5777–5781. doi:10.1039/c6gc01888b

CrossRef Full Text | Google Scholar

Hou, P., Ma, M., Zhang, P., Cao, J., Liu, H., Xu, X., et al. (2021). Catalytic Transfer Hydrogenation of Furfural to Furfuryl Alcohol Using Easy-To-Separate Core-Shell Magnetic Zirconium Hydroxide. New J. Chem. 45, 2715–2722. doi:10.1039/d0nj05638c

CrossRef Full Text | Google Scholar

Hu, D., Xu, H., Wu, Z., Zhang, M., Zhao, Z., Wang, Y., et al. (2021). Noble Metal-free Hierarchical ZrY Zeolite Efficient for Hydrogenation of Biomass-Derived Levulinic Acid. Front. Chem. 9, 725175. doi:10.3389/fchem.2021.725175

PubMed Abstract | CrossRef Full Text | Google Scholar

Hu, F., Wang, Y., Xu, S., Zhang, Z., Chen, Y., Fan, J., et al. (2019). Efficient and Selective Ni/Al2O3-C Catalyst Derived from Metal-Organic Frameworks for the Hydrogenation of Furfural to Furfuryl Alcohol. Catal. Lett. 149, 2158–2168. doi:10.1007/s10562-019-02766-y

CrossRef Full Text | Google Scholar

Hu, L., Dai, X., Li, N., Tang, X., and Jiang, Y. (2019). Highly Selective Hydrogenation of Biomass-Derived 5-hydroxymethylfurfural into 2,5-bis(hydroxymethyl)furan over an Acid-Base Bifunctional Hafnium-Based Coordination Polymer Catalyst. Sustain. Energ. Fuels 3, 1033–1041. doi:10.1039/c8se00545a

CrossRef Full Text | Google Scholar

Hu, L., Li, T., Xu, J., He, A., Tang, X., Chu, X., et al. (2018). Catalytic Transfer Hydrogenation of Biomass-Derived 5-hydroxymethylfurfural into 2,5-dihydroxymethylfuran over Magnetic Zirconium-Based Coordination Polymer. Chem. Eng. J. 352, 110–119. doi:10.1016/j.cej.2018.07.007

CrossRef Full Text | Google Scholar

Hu, L., Yang, M., Xu, N., Xu, J., Zhou, S., Chu, X., et al. (2017). Selective Transformation of Biomass-Derived 5-hydroxymethylfurfural into 2,5-dihydroxymethylfuran via Catalytic Transfer Hydrogenation over Magnetic Zirconium Hydroxides. Korean J. Chem. Eng. 35, 99–109. doi:10.1007/s11814-017-0238-3

CrossRef Full Text | Google Scholar

Hu, Z., Peng, Y., Gao, Y., Qian, Y., Ying, S., Yuan, D., et al. (2016). Direct Synthesis of Hierarchically Porous Metal-Organic Frameworks with High Stability and Strong Brønsted Acidity: The Decisive Role of Hafnium in Efficient and Selective Fructose Dehydration. Chem. Mater. 28, 2659–2667. doi:10.1021/acs.chemmater.6b00139

CrossRef Full Text | Google Scholar

Huang, R., Cui, Q., Yuan, Q., Wu, H., Guan, Y., and Wu, P. (2018). Total Hydrogenation of Furfural over Pd/Al2O3 and Ru/ZrO2 Mixture under Mild Conditions: Essential Role of Tetrahydrofurfural as an Intermediate and Support Effect. ACS Sustain. Chem. Eng. 6, 6957–6964. doi:10.1021/acssuschemeng.8b00801

CrossRef Full Text | Google Scholar

Iglesias, J., Martínez-Salazar, I., Maireles-Torres, P., Martin Alonso, D., Mariscal, R., and López Granados, M. (2020). Advances in Catalytic Routes for the Production of Carboxylic Acids from Biomass: A Step Forward for Sustainable Polymers. Chem. Soc. Rev., 49, 5704--5771. doi:10.1039/d0cs00177e

CrossRef Full Text | Google Scholar

Iglesias, J., Melero, J. A., Morales, G., Paniagua, M., Hernández, B., Osatiashtiani, A., et al. (2018). ZrO2-SBA-15 Catalysts for the One-Pot cascade Synthesis of GVL from Furfural. Catal. Sci. Technol. 8, 4485–4493. doi:10.1039/c8cy01121d

CrossRef Full Text | Google Scholar

Iglesias, J., Melero, J., Morales, G., Moreno, J., Segura, Y., Paniagua, M., et al. (2015). Zr-SBA-15 Lewis Acid Catalyst: Activity in Meerwein Ponndorf Verley Reduction. Catalysts 5, 1911–1927. doi:10.3390/catal5041911

CrossRef Full Text | Google Scholar

Injongkol, Y., Maihom, T., Treesukul, P., Sirijaraensre, J., Boekfa, B., and Limtrakul, J. (2017). Theoretical Study on the Reaction Mechanism of Hydrogenation of Furfural to Furfuryl Alcohol on lewis Acidic Bea Zeolites: Effects of Defect Structure and Tetravalent Metals Substitution. Phys. Chem. Chem. Phys. 19, 24042–24048. doi:10.1039/c7cp04229a

PubMed Abstract | CrossRef Full Text | Google Scholar

Iriondo, A., Mendiguren, A., Güemez, M. B., Requies, J., and Cambra, J. F. (2017). 2,5-DMF Production through Hydrogenation of Real and Synthetic 5-HMF over Transition Metal Catalysts Supported on Carriers with Different Nature. Catal. Today 279, 286–295. doi:10.1016/j.cattod.2016.02.019

CrossRef Full Text | Google Scholar

Ishikawa, S., Jones, D. R., Iqbal, S., Reece, C., Morgan, D. J., Willock, D. J., et al. (2017). Identification of the Catalytically Active Component of Cu-Zr-O Catalyst for the Hydrogenation of Levulinic Acid to γ-valerolactone. Green. Chem. 19, 225–236. doi:10.1039/c6gc02598f

CrossRef Full Text | Google Scholar

Jain, A., Shore, A. M., Jonnalagadda, S. C., Ramanujachary, K. V., and Mugweru, A. (2015). Conversion of Fructose, Glucose and Sucrose to 5-Hydroxymethyl-2-Furfural over Mesoporous Zirconium Phosphate Catalyst. Appl. Catal. A: Gen. 489, 72–76. doi:10.1016/j.apcata.2014.10.020

CrossRef Full Text | Google Scholar

Jiang, S., Li, F., Huang, J., Wang, Y., Lu, S., Li, P., et al. (2020). Catalytic Transfer Hydrogenation of Furfural over Magnetic Carbon‐Encapsulated CoO@C Catalyst. Chemistryselect 5, 9883–9892. doi:10.1002/slct.202002269

CrossRef Full Text | Google Scholar

Jin, W., Pastor-Pérez, L., Shen, D., Sepúlveda-Escribano, A., Gu, S., and Ramirez Reina, T.( 2019).Catalytic Upgrading of Biomass Model Compounds: Novel Approaches and Lessons Learnt from Traditional Hydrodeoxygenation - a Review .ChemCatChem 11 ,924 -960.doi:10.1002/cctc.201801722

CrossRef Full Text | Google Scholar

Karthik, V., Selvakumar, P., Senthil Kumar, P., Vo, D.-V. N., Gokulakrishnan, M., Keerthana, P., et al. (2021). Graphene-based Materials for Environmental Applications: A Review. Environ. Chem. Lett. 19, 3631–3644. doi:10.1007/s10311-021-01262-3

CrossRef Full Text | Google Scholar

Kerkel, F., Markiewicz, M., Stolte, S., Müller, E., and Kunz, W. (2021). The green Platform Molecule Gamma-Valerolactone - Ecotoxicity, Biodegradability, Solvent Properties, and Potential Applications. Green. Chem. 23, 2962–2976. doi:10.1039/d0gc04353b

CrossRef Full Text | Google Scholar

Khan, K., Tareen, A. K., Iqbal, M., Shi, Z., Zhang, H., and Guo, Z. (2021). Novel Emerging Graphdiyne Based Two Dimensional Materials: Synthesis, Properties and Renewable Energy Applications. Nano Today 39, 101207. doi:10.1016/j.nantod.2021.101207

CrossRef Full Text | Google Scholar

Kim, K. D., Kim, J., Teoh, W. Y., Kim, J.-C., Huang, J., and Ryoo, R. (2020). Cascade Reaction Engineering on Zirconia-Supported Mesoporous MFI Zeolites with Tunable Lewis-Brønsted Acid Sites: a Case of the One-Pot Conversion of Furfural to γ-valerolactone. RSC Adv. 10, 35318–35328. doi:10.1039/d0ra06915a

CrossRef Full Text | Google Scholar

Koreniuk, A., Maresz, K., and Mrowiec-Białoń, J. (2015). Supported Zirconium-Based Continuous-Flow Microreactor for Effective Meerwein-Ponndorf-Verley Reduction of Cyclohexanone. Catal. Commun. 64, 48–51. doi:10.1016/j.catcom.2015.01.021

CrossRef Full Text | Google Scholar

Kou, H., Luo, W., Huang, Z., Sang, G., Hu, C., Chen, C., et al. (2016). Effects of Temperature and Hydrogen Pressure on the Activation Behavior of Zrco. Int. J. Hydrogen Energ. 41, 10811–10818. doi:10.1016/j.ijhydene.2016.05.011

CrossRef Full Text | Google Scholar

Kumar, A., Kumar, N., Baredar, P., and Shukla, A. (2015). A Review on Biomass Energy Resources, Potential, Conversion and Policy in india. Renew. Sustain. Energ. Rev. 45, 530–539. doi:10.1016/j.rser.2015.02.007

CrossRef Full Text | Google Scholar

Kuwahara, Y., Kaburagi, W., and Fujitani, T. (2014). Catalytic Conversion of Levulinic Acid and its Esters to γ-Valerolactone over Silica-Supported Zirconia Catalysts. Bcsj 87, 1252–1254. doi:10.1246/bcsj.20140205

CrossRef Full Text | Google Scholar

Kuwahara, Y., Kaburagi, W., Osada, Y., Fujitani, T., and Yamashita, H. (2017). Catalytic Transfer Hydrogenation of Biomass-Derived Levulinic Acid and its Esters to γ-valerolactone over ZrO 2 Catalyst Supported on SBA-15 Silica. Catal. Today 281, 418–428. doi:10.1016/j.cattod.2016.05.016

CrossRef Full Text | Google Scholar

Kuwahara, Y., Kango, H., and Yamashita, H. (2016). Catalytic Transfer Hydrogenation of Biomass-Derived Levulinic Acid and its Esters to γ-Valerolactone over Sulfonic Acid-Functionalized UiO-66. ACS Sustain. Chem. Eng. 5, 1141–1152. doi:10.1021/acssuschemeng.6b02464

CrossRef Full Text | Google Scholar

Li, F., France, L. J., Cai, Z., Li, Y., Liu, S., Lou, H., et al. (2017). Catalytic Transfer Hydrogenation of Butyl Levulinate to γ-valerolactone over Zirconium Phosphates with Adjustable Lewis and Brønsted Acid Sites. Appl. Catal. B: Environ. 214, 67–77. doi:10.1016/j.apcatb.2017.05.013

CrossRef Full Text | Google Scholar

Li, H., Dai, M., Dai, S., and Dong, X. (2018a). Current Status and Environment Impact of Direct Straw Return in china's Cropland - a Review. Ecotoxicology Environ. Saf. 159, 293–300. doi:10.1016/j.ecoenv.2018.05.014

CrossRef Full Text | Google Scholar

Li, H., Fang, Z., Smith, R. L., and Yang, S. (2016a). Efficient Valorization of Biomass to Biofuels with Bifunctional Solid Catalytic Materials. Prog. Energ. Combustion Sci. 55, 98–194. doi:10.1016/j.pecs.2016.04.004

CrossRef Full Text | Google Scholar

Li, H., Fang, Z., and Yang, S. (2016a). Direct Catalytic Transformation of Biomass Derivatives into Biofuel Component γ-Valerolactone with Magnetic Nickel-Zirconium Nanoparticles. Chempluschem 81, 135–142. doi:10.1002/cplu.201500492

PubMed Abstract | CrossRef Full Text | Google Scholar

Li, H., Fang, Z., and Yang, S. (2015). Direct Conversion of Sugars and Ethyl Levulinate into γ-Valerolactone with Superparamagnetic Acid-Base Bifunctional ZrFeOx Nanocatalysts. ACS Sustain. Chem. Eng. 4, 236–246. doi:10.1021/acssuschemeng.5b01480

CrossRef Full Text | Google Scholar

Li, H., Guo, H., Fang, Z., Aida, T. M., and Smith, R. L. (2020a). Cycloamination Strategies for Renewable N-Heterocycles. Green. Chem. 22, 582–611. doi:10.1039/c9gc03655e

CrossRef Full Text | Google Scholar

Li, H., He, J., Riisager, A., Saravanamurugan, S., Song, B., and Yang, S. (2016c). Acid-Base Bifunctional Zirconium N-Alkyltriphosphate Nanohybrid for Hydrogen Transfer of Biomass-Derived Carboxides. ACS Catal. 6, 7722–7727. doi:10.1021/acscatal.6b02431

CrossRef Full Text | Google Scholar

Li, H., Li, Y., Fang, Z., and Smith, R. L. (2019a). Efficient Catalytic Transfer Hydrogenation of Biomass-Based Furfural to Furfuryl Alcohol with Recycable Hf-Phenylphosphonate Nanohybrids. Catal. Today 319, 84–92. doi:10.1016/j.cattod.2018.04.056

CrossRef Full Text | Google Scholar

Li, H., Wang, C., Xu, Y., Yu, Z., Saravanamurugan, S., Wu, Z., et al. (2020b). Heterogeneous (de)chlorination-enabled control of reactivity in the liquid-phase synthesis of furanic biofuel from cellulosic feedstock. Green. Chem. 22, 637–645. doi:10.1039/c9gc04092g

CrossRef Full Text | Google Scholar

Li, H., Wu, H., Zhang, H., Su, Y., Yang, S., and Hensen, E. J. M. (2019b). A Facile Direct Route to N ‐(Un)substituted Lactams by Cycloamination of Oxocarboxylic Acids without External Hydrogen. Chemsuschem 12, 3778–3784. doi:10.1002/cssc.201901780

PubMed Abstract | CrossRef Full Text | Google Scholar

Li, H., Yang, T., and Fang, Z. (2018b). Biomass-derived Mesoporous Hf-Containing Hybrid for Efficient Meerwein-Ponndorf-Verley Reduction at Low Temperatures. Appl. Catal. B: Environ. 227, 79–89. doi:10.1016/j.apcatb.2018.01.017

CrossRef Full Text | Google Scholar

Li, H., Zhao, W., Dai, W., Long, J., Watanabe, M., Meier, S., et al. (2018). Noble Metal-free Upgrading of Multi-Unsaturated Biomass Derivatives at Room Temperature: Silyl Species Enable Reactivity. Green. Chem. 20, 5327–5335. doi:10.1039/c8gc02934b

CrossRef Full Text | Google Scholar

Li, H., Zhao, W., Saravanamurugan, S., Dai, W., He, J., Meier, S., et al. (2018). Control of Selectivity in Hydrosilane-Promoted Heterogeneous Palladium-Catalysed Reduction of Furfural and Aromatic Carboxides. Commun. Chem. 1. doi:10.1038/s42004-018-0033-z

CrossRef Full Text | Google Scholar

Li, J., Zhao, S., Li, Z., Liu, D., Chi, Y., and Hu, C. (2021). Efficient Conversion of Biomass-Derived Levulinic Acid to γ-Valerolactone over Polyoxometalate@Zr-Based Metal-Organic Frameworks: The Synergistic Effect of Bro̷nsted and Lewis Acidic Sites. Inorg. Chem. 60, 7785–7793. doi:10.1021/acs.inorgchem.1c00185

PubMed Abstract | CrossRef Full Text | Google Scholar

Li, M., Liu, Y., Lin, X., Tan, J., Yang, S., and Li, H. (2021). One-step Upgrading of Bio-Based Furfural to γ-valerolactone via HfCl4-Mediated Bifunctional Catalysis. RSC Adv. 11, 35415–35424. doi:10.1039/d1ra05637a

CrossRef Full Text | Google Scholar

Li, W., Cai, Z., Li, H., Shen, Y., Zhu, Y., Li, H., et al. (2019). Hf-based Metal Organic Frameworks as Bifunctional Catalysts for the One-Pot Conversion of Furfural to γ-valerolactone. Mol. Catal. 472, 17–26. doi:10.1016/j.mcat.2019.04.010

CrossRef Full Text | Google Scholar

Li, X., Du, Z., Wu, Y., Zhen, Y., Shao, R., Li, B., et al. (2020). A Novel Hafnium-Graphite Oxide Catalyst for the Meerwein-Ponndorf-Verley Reaction and the Activation Effect of the Solvent. RSC Adv. 10, 9985–9995. doi:10.1039/c9ra10795a

CrossRef Full Text | Google Scholar

Li, X., and Jiang, J. (2019). Molecular Design of Chiral Zirconium Metal-Organic Frameworks for Asymmetric Transfer Hydrogenation of Imines. Catal. Sci. Technol. 9, 4888–4897. doi:10.1039/c9cy00770a

CrossRef Full Text | Google Scholar

Liao, Y., Liu, Q., Wang, T., Long, J., Ma, L., and Zhang, Q. (2014). Zirconium Phosphate Combined with Ru/C as a Highly Efficient Catalyst for the Direct Transformation of Cellulose to C6 Alditols. Green. Chem. 16, 3305–3312. doi:10.1039/c3gc42444h

CrossRef Full Text | Google Scholar

Lin, Y., Bu, Q., Xu, J., Liu, X., Zhang, X., Lu, G.-P., et al. (2021). Hf-MOF Catalyzed Meerwein−Ponndorf−Verley (MPV) Reduction Reaction: Insight into Reaction Mechanism. Mol. Catal. 502, 111405. doi:10.1016/j.mcat.2021.111405

CrossRef Full Text | Google Scholar

Liu, C., Wei, L., Yin, X., Pan, X., Hu, J., Li, N., et al. (2021). Synthesis of Furfural from Xylan in γ-valerolactone/molten Salt Hydrate Biphasic System. Chem. Eng. J. 425, 130608. doi:10.1016/j.cej.2021.130608

CrossRef Full Text | Google Scholar

Liu, C., Xu, G., Hu, A., Xie, Y., and Wang, H. (2019). Porous Zirconium Hydroxyphosphonoacetate: Catalyst for Conversion of Furfural into Furfuryl Alcohol. Chemistryselect 4, 8000–8006. doi:10.1002/slct.201901612

CrossRef Full Text | Google Scholar

Liu, K., Qin, R., and Zheng, N. (2021). Insights into the Interfacial Effects in Heterogeneous Metal Nanocatalysts toward Selective Hydrogenation. J. Am. Chem. Soc. 143, 4483–4499. doi:10.1021/jacs.0c13185

CrossRef Full Text | Google Scholar

Liu, S. H., Jaenicke, S., and Chuah, G. K. (2002). Hydrous Zirconia as a Selective Catalyst for the Meerwein-Ponndorf-Verley Reduction of Cinnamaldehyde. J. Catal. 206, 321–330. doi:10.1006/jcat.2001.3480

CrossRef Full Text | Google Scholar

Liu, S., Meng, Y., Li, H., and Yang, S. (2021). Hierarchical Porous mil-101(Cr) Solid Acid-Catalyzed Production of Value-Added Acetals from Biomass-Derived Furfural. Polymers 13, 3498. doi:10.3390/polym13203498

PubMed Abstract | CrossRef Full Text | Google Scholar

Liu, X., Yin, B., Zhang, W., Yu, X., Du, Y., Zhao, S., et al. (2021). Catalytic Transfer Hydrogenolysis of Glycerol over Heterogeneous Catalysts: A Short Review on Mechanistic Studies. Chem. Rec. 21, 1792–1810. doi:10.1002/tcr.202100037

PubMed Abstract | CrossRef Full Text | Google Scholar

Liu, Y., Chen, D., Li, M., Zhang, H., and Li, H. (2021). Catalytic Stereoselective Conversion of Biomass-Derived 4′-Methoxypropiophenone to Trans-anethole with a Bifunctional and Recyclable Hf-Based Polymeric Nanocatalyst. Polymers 13, 2808. doi:10.3390/polym13162808

PubMed Abstract | CrossRef Full Text | Google Scholar

Luo, H. Y., Consoli, D. F., Gunther, W. R., and Román-Leshkov, Y. (2014). Investigation of the Reaction Kinetics of Isolated Lewis Acid Sites in Beta Zeolites for the Meerwein-Ponndorf-Verley Reduction of Methyl Levulinate to γ-valerolactone. J. Catal. 320, 198–207. doi:10.1016/j.jcat.2014.10.010

CrossRef Full Text | Google Scholar

Luo, Y.-J., Zhou, Y.-H., and Huang, Y.-B. (2018). A New lewis Acidic Zr Catalyst for the Synthesis of Furanic Diesel Precursor from Biomass Derived Furfural and 2-methylfuran. Catal. Lett. 149, 292–302. doi:10.1007/s10562-018-2599-6

CrossRef Full Text | Google Scholar

Luo, Y., Li, Z., Li, X., Liu, X., Fan, J., Clark, J. H., et al. (2019). The Production of Furfural Directly from Hemicellulose in Lignocellulosic Biomass: A Review. Catal. Today 319, 14–24. doi:10.1016/j.cattod.2018.06.042

CrossRef Full Text | Google Scholar

Ma, M., Yan, X., Hou, P., Cao, J., Liu, H., Xu, X., et al. (2020). One‐Pot Transfer Hydrogenation of Methyl Levulinate into Valerolactone and 1,4‐pentanediol over In Situ Reduced Cu/ZrOCO3 in 2‐PrOH. Chemistryselect 5, 924–930. doi:10.1002/slct.201904480

CrossRef Full Text | Google Scholar

Mardiana, S., Azhari, N. J., Ilmi, T., and Kadja, G. T. M. (2022). Hierarchical Zeolite for Biomass Conversion to Biofuel: A Review. Fuel 309, 122119. doi:10.1016/j.fuel.2021.122119

CrossRef Full Text | Google Scholar

Mathimani, T., and Mallick, N. (2019). A Review on the Hydrothermal Processing of Microalgal Biomass to Bio-Oil - Knowledge Gaps and Recent Advances. J. Clean. Prod. 217, 69–84. doi:10.1016/j.jclepro.2019.01.129

CrossRef Full Text | Google Scholar

Mautschke, H. H., and Llabrés i Xamena, F. X. (2021). One‐Step Chemo‐, Regio‐ and Stereoselective Reduction of Ketosteroids to Hydroxysteroids over Zr‐Containing MOF‐808 Metal‐Organic Frameworks. Chem. Eur. J. 27, 10766–10775. doi:10.1002/chem.202100967

CrossRef Full Text | Google Scholar

Melero, J. A., Morales, G., Iglesias, J., Paniagua, M., and López-Aguado, C. (2018). Rational Optimization of Reaction Conditions for the One-Pot Transformation of Furfural to γ-Valerolactone over Zr-Al-Beta Zeolite: Toward the Efficient Utilization of Biomass. Ind. Eng. Chem. Res. 57, 11592–11599. doi:10.1021/acs.iecr.8b02475

CrossRef Full Text | Google Scholar

Melero, J. A., Morales, G., Iglesias, J., Paniagua, M., López-Aguado, C., Wilson, K., et al. (2017). Efficient One-Pot Production of γ-valerolactone from Xylose over Zr-Al-Beta Zeolite: Rational Optimization of Catalyst Synthesis and Reaction Conditions. Green. Chem. 19, 5114–5121. doi:10.1039/c7gc01969f

CrossRef Full Text | Google Scholar

Mondelli, C., Gözaydın, G., Yan, N., and Pérez-Ramírez, J. (2020). Biomass Valorisation over Metal-Based Solid Catalysts from Nanoparticles to Single Atoms. Chem. Soc. Rev. 49, 3764–3782. doi:10.1039/d0cs00130a

PubMed Abstract | CrossRef Full Text | Google Scholar

Nguyen, L. H. T., Nguyen, T. T. T., Tran, P. H., Kawazoe, Y., Le, H. M., and Doan, T. L. H. (2019). Zr and Hf-Metal-Organic Frameworks: Efficient and Recyclable Heterogeneous Catalysts for the Synthesis of 2-arylbenzoxazole via Ring Open Pathway Acylation Reaction. J. Catal. 374, 110–117. doi:10.1016/j.jcat.2019.04.023

CrossRef Full Text | Google Scholar

Osman, A. I., Mehta, N., Elgarahy, A. M., Al-Hinai, A., Al-Muhtaseb, A. a. H., and Rooney, D. W. (2021). Conversion of Biomass to Biofuels and Life Cycle Assessment: A Review. Environ. Chem. Lett. 19, 4075–4118. doi:10.1007/s10311-021-01273-0

CrossRef Full Text | Google Scholar

Palermo, V., Kinloch, I. A., Ligi, S., and Pugno, N. M. (2016). Nanoscale Mechanics of Graphene and Graphene Oxide in Composites: A Scientific and Technological Perspective. Adv. Mater. 28, 6232–6238. doi:10.1002/adma.201505469

PubMed Abstract | CrossRef Full Text | Google Scholar

Pan, H., Xia, Q., Li, H., Wang, Y., Shen, Z., Wang, Y., et al. (2022). Direct Production of Biodiesel from Crude euphorbia Lathyris L. Oil Catalyzed by Multifunctional Mesoporous Composite Materials. Fuel 309, 122172. doi:10.1016/j.fuel.2021.122172

CrossRef Full Text | Google Scholar

Pang, J., Sun, J., Zheng, M., Li, H., Wang, Y., and Zhang, T. (2019). Transition Metal Carbide Catalysts for Biomass Conversion: A Review. Appl. Catal. B: Environ. 254, 510–522. doi:10.1016/j.apcatb.2019.05.034

CrossRef Full Text | Google Scholar

Paniagua, M., Morales, G., Melero, J. A., Iglesias, J., López-Aguado, C., Vidal, N., et al. (2021). Understanding the Role of Al/Zr Ratio in Zr-Al-Beta Zeolite: Towards the One-Pot Production of Gvl from Glucose. Catal. Today 367, 228–238. doi:10.1016/j.cattod.2020.04.025

CrossRef Full Text | Google Scholar

Pattnaik, F., Tripathi, S., Patra, B. R., Nanda, S., Kumar, V., Dalai, A. K., et al. (2021). Catalytic Conversion of Lignocellulosic Polysaccharides to Commodity Biochemicals: A Review. Environ. Chem. Lett. 19, 4119–4136. doi:10.1007/s10311-021-01284-x

CrossRef Full Text | Google Scholar

Peng, Q., Wang, H., Xia, Y., and Liu, X. (2021). One-pot Conversion of Furfural to Gamma-Valerolactone in the Presence of Multifunctional Zirconium Alizarin Red S Hybrid. Appl. Catal. A: Gen. 621, 118203. doi:10.1016/j.apcata.2021.118203

CrossRef Full Text | Google Scholar

Prasertsab, A., Maihom, T., Probst, M., Wattanakit, C., and Limtrakul, J. (2018). Furfural to Furfuryl Alcohol: Computational Study of the Hydrogen Transfer on lewis Acidic Bea Zeolites and Effects of Cation Exchange and Tetravalent Metal Substitution. Inorg. Chem. 57, 6599–6605. doi:10.1021/acs.inorgchem.8b00741

PubMed Abstract | CrossRef Full Text | Google Scholar

Prasomsri, T., Nimmanwudipong, T., and Román-Leshkov, Y. (2013). Effective Hydrodeoxygenation of Biomass-Derived Oxygenates into Unsaturated Hydrocarbons by Moo3 Using Low H2 Pressures. Energy Environ. Sci. 6, 1732–1738. doi:10.1039/c3ee24360e

CrossRef Full Text | Google Scholar

Priecel, P., Endot, N. A., Carà, P. D., and Lopez-Sanchez, J. A. (2018). Fast Catalytic Hydrogenation of 2,5-hydroxymethylfurfural to 2,5-dimethylfuran with Ruthenium on Carbon Nanotubes. Ind. Eng. Chem. Res. 57, 1991–2002. doi:10.1021/acs.iecr.7b04715

CrossRef Full Text | Google Scholar

Ramanathan, A., Castro Villalobos, M. C., Kwakernaak, C., Telalovic, S., and Hanefeld, U. (2008). Zr-TUD-1: A lewis Acidic, Three-Dimensional, Mesoporous, Zirconium-Containing Catalyst. Chem. Eur. J. 14, 961–972. doi:10.1002/chem.200700725

PubMed Abstract | CrossRef Full Text | Google Scholar

Rode, A., Carleton, T., Delgado, M., Greenstone, M., Houser, T., Hsiang, S., et al. (2021). Estimating a Social Cost of Carbon for Global Energy Consumption. Nature 598, 308–314. doi:10.1038/s41586-021-03883-8

PubMed Abstract | CrossRef Full Text | Google Scholar

Rojas-Buzo, S., García-García, P., and Corma, A. (2018). Catalytic Transfer Hydrogenation of Biomass-Derived Carbonyls over Hafnium-Based Metal-Organic Frameworks. Chemsuschem 11, 432–438. doi:10.1002/cssc.201701708

PubMed Abstract | CrossRef Full Text | Google Scholar

Rui, T., Lu, G.-P., Zhao, X., Cao, X., and Chen, Z. (2021). The Synergistic Catalysis on Co Nanoparticles and Conx Sites of Aniline-Modified Zif Derived Co@ncs for Oxidative Esterification of HMF. Chin. Chem. Lett. 32, 685–690. doi:10.1016/j.cclet.2020.06.027

CrossRef Full Text | Google Scholar

Sabyrzhan, A., Balgimbekova, G., and Shestak, V. (2021). Economic and Legal Regulation of the Use and Development of Renewable Energy Sources. Int. Environ. Agreements 21, 595–610. doi:10.1007/s10784-021-09532-9

CrossRef Full Text | Google Scholar

Sakakibara, K., Endo, K., and Osawa, T. (2019). Facile Synthesis of γ-valerolactone by Transfer Hydrogenation of Methyl Levulinate and Levulinic Acid over Ni/ZrO2. Catal. Commun. 125, 52–55. doi:10.1016/j.catcom.2019.03.021

CrossRef Full Text | Google Scholar

Santana, C. G., and Krische, M. J. (2021). From Hydrogenation to Transfer Hydrogenation to Hydrogen Auto-Transfer in Enantioselective Metal-Catalyzed Carbonyl Reductive Coupling: Past, Present, and Future. ACS Catal. 11, 5572–5585. doi:10.1021/acscatal.1c01109

PubMed Abstract | CrossRef Full Text | Google Scholar

Sarkar, C., Paul, R., Chandra Shit, S., Trinh, Q. T., Koley, P., Rao, B. S., et al. (2021). Navigating Copper-Atom-Pair Structural Effect inside a Porous Organic Polymer Cavity for Selective Hydrogenation of Biomass-Derived 5-hydroxymethylfurfural. ACS Sustain. Chem. Eng. 9, 2136–2151. doi:10.1021/acssuschemeng.0c07594

CrossRef Full Text | Google Scholar

Schwarzman, M., Schildroth, S., Bhetraratana, M., Alvarado, Á., and Balmes, J. (2021). Raising Standards to Lower Diesel Emissions. Science 371, 1314–1316. doi:10.1126/science.abf8159

PubMed Abstract | CrossRef Full Text | Google Scholar

Sha, Y., Xiao, Z., Zhou, H., Yang, K., Song, Y., Li, N., et al. (2017). Direct Use of Humic Acid Mixtures to Construct Efficient Zr-Containing Catalysts for Meerwein-Ponndorf-Verley Reactions. Green. Chem. 19, 4829–4837. doi:10.1039/c7gc01925d

CrossRef Full Text | Google Scholar

Shao, Y., Li, Q., Dong, X., Wang, J., Sun, K., Zhang, L., et al. (2021). Cooperation between Hydrogenation and Acidic Sites in Cu-Based Catalyst for Selective Conversion of Furfural to γ-valerolactone. Fuel 293, 120457. doi:10.1016/j.fuel.2021.120457

CrossRef Full Text | Google Scholar

Shearer, G. C., Chavan, S., Ethiraj, J., Vitillo, J. G., Svelle, S., Olsbye, U., et al. (2014). Tuned to Perfection: Ironing Out the Defects in Metal-Organic Framework UiO-66. Chem. Mater. 26, 4068–4071. doi:10.1021/cm501859p

CrossRef Full Text | Google Scholar

Shen, S., Chen, J., Koodali, R. T., Hu, Y., Xiao, Q., Zhou, J., et al. (2014). Activation of MCM-41 Mesoporous Silica by Transition-Metal Incorporation for Photocatalytic Hydrogen Production. Appl. Catal. B: Environ. 150-151, 138–146. doi:10.1016/j.apcatb.2013.12.014

CrossRef Full Text | Google Scholar

Shi, D., Yang, Q., Peterson, C., Lamic-Humblot, A.-F., Girardon, J.-S., Griboval-Constant, A., et al. (2019). Bimetallic Fe-Ni/SiO2 Catalysts for Furfural Hydrogenation: Identification of the Interplay between Fe and Ni during Deposition-Precipitation and thermal Treatments. Catal. Today 334, 162–172. doi:10.1016/j.cattod.2018.11.041

CrossRef Full Text | Google Scholar

Silbernagel, R., Martin, C. H., and Clearfield, A. (2016). Zirconium(iv) Phosphonate-Phosphates as Efficient Ion-Exchange Materials. Inorg. Chem. 55, 1651–1656. doi:10.1021/acs.inorgchem.5b02555

PubMed Abstract | CrossRef Full Text | Google Scholar

Singh, J., Suhag, M., and Dhaka, A. (2015). Augmented Digestion of Lignocellulose by Steam Explosion, Acid and Alkaline Pretreatment Methods: A Review. Carbohydr. Polym. 117, 624–631. doi:10.1016/j.carbpol.2014.10.012

PubMed Abstract | CrossRef Full Text | Google Scholar

Solanki, B. S., and Rode, C. V. (2019). Selective Hydrogenation of 5-HMF to 2,5-DMF over a Magnetically Recoverable Non-noble Metal Catalyst. Green. Chem. 21, 6390–6406. doi:10.1039/c9gc03091c

CrossRef Full Text | Google Scholar

Song, J., Hua, M., Huang, X., Visa, A., Wu, T., Fan, H., et al. (2021). Highly Efficient Meerwein-Ponndorf-Verley Reductions over a Robust Zirconium-Organoboronic Acid Hybrid. Green. Chem. 23, 1259–1265. doi:10.1039/d0gc04179c

CrossRef Full Text | Google Scholar

Song, J., Wu, L., Zhou, B., Zhou, H., Fan, H., Yang, Y., et al. (2015). A New Porous Zr-Containing Catalyst with a Phenate Group: an Efficient Catalyst for the Catalytic Transfer Hydrogenation of Ethyl Levulinate to γ-valerolactone. Green. Chem. 17, 1626–1632. doi:10.1039/c4gc02104e

CrossRef Full Text | Google Scholar

Song, J., Zhou, B., Zhou, H., Wu, L., Meng, Q., Liu, Z., et al. (2015). Porous Zirconium-Phytic Acid Hybrid: A Highly Efficient Catalyst for Meerwein-Ponndorf-Verley Reductions. Angew. Chem. Int. Ed. 54, 9399–9403. doi:10.1002/anie.201504001

PubMed Abstract | CrossRef Full Text | Google Scholar

Spinelli, R., Visser, R., Björheden, R., and Röser, D. (2019). Recovering Energy Biomass in Conventional forest Operations: A Review of Integrated Harvesting Systems. Curr. For. Rep 5, 90–100. doi:10.1007/s40725-019-00089-0

CrossRef Full Text | Google Scholar

Srinivasa Rao, B., Krishna Kumari, P., Dhana Lakshmi, D., and Lingaiah, N. (2018). One Pot Selective Transformation of Biomass Derived Chemicals towards Alkyl Levulinates over Titanium Exchanged Heteropoly Tungstate Catalysts. Catal. Today 309, 269–275. doi:10.1016/j.cattod.2017.05.040

CrossRef Full Text | Google Scholar

Srinivasa Rao, B., Yogita Dhana Lakshmi, D., Dhana Lakshmi, D., Kumari, P. K., and Lingaiah, N. 2021). Influence of Metal Oxide and Heteropoly Tungstate Location in Mesoporous Silica towards Catalytic Transfer Hydrogenation of Furfural to γ-valerolactone. Sustain. Energ. Fuels 5, 3719–3728. doi:10.1039/d1se00340b

CrossRef Full Text | Google Scholar

Sudarsanam, P., Li, H., and Sagar, T. V. (2020). TiO2-Based Water-Tolerant Acid Catalysis for Biomass-Based Fuels and Chemicals. ACS Catal. 10, 9555–9584. doi:10.1021/acscatal.0c01680

CrossRef Full Text | Google Scholar

Sullivan, M. M., Chen, C.-J., and Bhan, A. (2016). Catalytic Deoxygenation on Transition Metal Carbide Catalysts. Catal. Sci. Technol. 6, 602–616. doi:10.1039/c5cy01665g

CrossRef Full Text | Google Scholar

Sushkevich, V. L., Ivanova, I. I., Tolborg, S., and Taarning, E. (2014). Meerwein-Ponndorf-Verley-Oppenauer Reaction of Crotonaldehyde with Ethanol over Zr-Containing Catalysts. J. Catal. 316, 121–129. doi:10.1016/j.jcat.2014.04.019

CrossRef Full Text | Google Scholar

Synowiecki, J., and Al-Khateeb, N. A. (2003). Production, Properties, and Some New Applications of Chitin and its Derivatives. Crit. Rev. Food Sci. Nutr. 43, 145–171. doi:10.1080/10408690390826473

PubMed Abstract | CrossRef Full Text | Google Scholar

Tan, J., Li, Y., Tan, X., Wu, H., Li, H., and Yang, S. (2021). Advances in Pretreatment of Straw Biomass for Sugar Production. Front. Chem. 9, 696030. doi:10.3389/fchem.2021.696030

PubMed Abstract | CrossRef Full Text | Google Scholar

Tan, X., Zhang, H., Li, H., and Yang, S. (2022). Electrovalent Bifunctional Acid Enables Heterogeneously Catalytic Production of Biodiesel by (Trans)esterification of Non-edible Oils. Fuel 310, 122273. doi:10.1016/j.fuel.2021.122273

CrossRef Full Text | Google Scholar

Tang, X., Chen, H., Hu, L., Hao, W., Sun, Y., Zeng, X., et al. (2014a). Conversion of Biomass to γ-valerolactone by Catalytic Transfer Hydrogenation of Ethyl Levulinate over Metal Hydroxides. Appl. Catal. B: Environ. 147, 827–834. doi:10.1016/j.apcatb.2013.10.021

CrossRef Full Text | Google Scholar

Tang, X., Hu, L., Sun, Y., Zhao, G., Hao, W., and Lin, L. (2013). Conversion of Biomass-Derived Ethyl Levulinate into γ-valerolactone via Hydrogen Transfer from Supercritical Ethanol over a ZrO2 Catalyst. RSC Adv.. 3, 10277. doi:10.1039/c3ra41288a

CrossRef Full Text | Google Scholar

Tang, X., Zeng, X., Li, Z., Hu, L., Sun, Y., Liu, S., et al. (2014b). Production of γ-valerolactone from Lignocellulosic Biomass for Sustainable Fuels and Chemicals Supply. Renew. Sustain. Energ. Rev. 40, 608–620. doi:10.1016/j.rser.2014.07.209

CrossRef Full Text | Google Scholar

Tang, X., Zeng, X., Li, Z., Li, W., Jiang, Y., Hu, L., et al. (2015). In Situ Generated Catalyst System to Convert Biomass-Derived Levulinic Acid to γ-Valerolactone. ChemCatChem 7, 1372–1379. doi:10.1002/cctc.201500115

CrossRef Full Text | Google Scholar

Taniya, K., Izumi, A., Ichihashi, Y., and Nishiyama, S. (2010). Influence of Preparation Methods of Supported Zr Oxide Catalysts for Meervein-Ponndorf-Verlay Reduction of Acetophenone. Msf 658, 420–423. doi:10.4028/www.scientific.net/msf.658.420

CrossRef Full Text | Google Scholar

Tian, Y., Zhang, F., Wang, J., Cao, L., and Han, Q. (2021). A Review on Solid Acid Catalysis for Sustainable Production of Levulinic Acid and Levulinate Esters from Biomass Derivatives. Bioresour. Techn. 342, 125977. doi:10.1016/j.biortech.2021.125977

CrossRef Full Text | Google Scholar

Tripathi, M., Sahu, J. N., and Ganesan, P. (2016). Effect of Process Parameters on Production of Biochar from Biomass Waste through Pyrolysis: A Review. Renew. Sustain. Energ. Rev. 55, 467–481. doi:10.1016/j.rser.2015.10.122

CrossRef Full Text | Google Scholar

Tuteja, J., Nishimura, S., and Ebitani, K. (2014). Base-free Chemoselective Transfer Hydrogenation of Nitroarenes to Anilines with Formic Acid as Hydrogen Source by a Reusable Heterogeneous Pd/ZrP Catalyst. RSC Adv.. 4, 38241–38249. doi:10.1039/c4ra06174h

CrossRef Full Text | Google Scholar

Valderrama Rios, M. L., González, A. M., Lora, E. E. S., and Almazán del Olmo, O. A. (2018). Reduction of Tar Generated during Biomass Gasification: A Review. Biomass and Bioenergy 108, 345–370. doi:10.1016/j.biombioe.2017.12.002

CrossRef Full Text | Google Scholar

Valekar, A. H., Cho, K.-H., Chitale, S. K., Hong, D.-Y., Cha, G.-Y., Lee, U.-H., et al. (2016). Catalytic Transfer Hydrogenation of Ethyl Levulinate to γ-valerolactone over Zirconium-Based Metal-Organic Frameworks. Green. Chem. 18, 4542–4552. doi:10.1039/c6gc00524a

CrossRef Full Text | Google Scholar

Valekar, A. H., Lee, M., Yoon, J. W., Kwak, J., Hong, D.-Y., Oh, K.-R., et al. (2020). Catalytic Transfer Hydrogenation of Furfural to Furfuryl Alcohol under Mild Conditions over Zr-MOFs: Exploring the Role of Metal Node Coordination and Modification. ACS Catal. 10, 3720–3732. doi:10.1021/acscatal.9b05085

CrossRef Full Text | Google Scholar

Wagner, M., Meyer, B., Setvin, M., Schmid, M., and Diebold, U. (2021). Direct Assessment of the Acidity of Individual Surface Hydroxyls. Nature 592, 722–725. doi:10.1038/s41586-021-03432-3

PubMed Abstract | CrossRef Full Text | Google Scholar

Wang, A., Sudarsanam, P., Xu, Y., Zhang, H., Li, H., and Yang, S. (2020). Functionalized Magnetic Nanosized Materials for Efficient Biodiesel Synthesis via Acid-Base/enzyme Catalysis. Green. Chem.. 22, 2977–3012. doi:10.1039/d0gc00924e

CrossRef Full Text | Google Scholar

Wang, C., Liu, X., Keser Demir, N., Chen, J. P., and Li, K. (2016). Applications of Water Stable Metal-Organic Frameworks. Chem. Soc. Rev. 45, 5107–5134. doi:10.1039/c6cs00362a

PubMed Abstract | CrossRef Full Text | Google Scholar

Wang, F., Yuan, Z., Liu, B., Chen, S., and Zhang, Z. (2016). Catalytic Oxidation of Biomass Derived 5-hydroxymethylfurfural (HMF) over Ru Iii -incorporated Zirconium Phosphate Catalyst. J. Ind. Eng. Chem. 38, 181–185. doi:10.1016/j.jiec.2016.05.001

CrossRef Full Text | Google Scholar

Wang, J., Jaenicke, S., and Chuah, G.-K. (2014). Zirconium-Beta Zeolite as a Robust Catalyst for the Transformation of Levulinic Acid to γ-valerolactone via Meerwein-Ponndorf-Verley Reduction. RSC Adv.. 4, 13481–13489. doi:10.1039/c4ra01120a

CrossRef Full Text | Google Scholar

Wang, T., He, J., and Zhang, Y. (2020). Production of γ-Valerolactone from One-Pot Transformation of Biomass-Derived Carbohydrates over Chitosan-Supported Ruthenium Catalyst Combined with Zeolite ZSM-5. Eur. J. Org. Chem. 2020, 1611–1619. doi:10.1002/ejoc.201901704

CrossRef Full Text | Google Scholar

Wang, T., Xu, H., He, J., and Zhang, Y. (2020). MPV Reduction of Ethyl Levulinate to γ-valerolactone by the Biomass-Derived Chitosan-Supported Zr Catalyst. New J. Chem. 44, 14686–14694. doi:10.1039/d0nj02667k

CrossRef Full Text | Google Scholar

Wang, X., Hao, J., Deng, L., Zhao, H., Liu, Q., Li, N., et al. (2020). The Construction of Novel and Efficient Hafnium Catalysts Using Naturally Existing Tannic Acid for Meerwein-Ponndorf-Verley Reduction. RSC Adv. 10, 6944–6952. doi:10.1039/c9ra10317a

CrossRef Full Text | Google Scholar

Wang, Y., Huang, J., Lu, S., Li, P., Xia, X., Li, C., et al. (2020). Phosphorus-modified Zirconium Metal Organic Frameworks for Catalytic Transfer Hydrogenation of Furfural. New J. Chem. 44, 20308–20315. doi:10.1039/d0nj04285d

CrossRef Full Text | Google Scholar

Wang, Y., Lewis, J. D., and Román-Leshkov, Y. (2016). Synthesis of Itaconic Acid Ester Analogues via Self-Aldol Condensation of Ethyl Pyruvate Catalyzed by Hafnium Bea Zeolites. ACS Catal.. 6, 2739–2744. doi:10.1021/acscatal.6b00561

CrossRef Full Text | Google Scholar

Wang, Y., Tong, X., Yan, Y., Xue, S., and Zhang, Y. (2014). Efficient and Selective Conversion of Hexose to 5-hydroxymethylfurfural with Tin-Zirconium-Containing Heterogeneous Catalysts. Catal. Commun. 50, 38–43. doi:10.1016/j.catcom.2014.02.023

CrossRef Full Text | Google Scholar

Wei, J., Jiang, L., Huang, M., Wu, Y., and Chen, S. (2021). Intrinsic Defect Limit to the Growth of Orthorhombic HfO 2 and (Hf,Zr)O 2 with Strong Ferroelectricity: First‐Principles Insights. Adv. Funct. Mater. 31, 2104913. doi:10.1002/adfm.202104913

CrossRef Full Text | Google Scholar

Welch, A. J., Digdaya, I. A., Kent, R., Ghougassian, P., Atwater, H. A., and Xiang, C. (2021). Comparative Technoeconomic Analysis of Renewable Generation of Methane Using Sunlight, Water, and Carbon Dioxide. ACS Energ. Lett.. 6, 1540–1549. doi:10.1021/acsenergylett.1c00174

CrossRef Full Text | Google Scholar

Winoto, H. P., Fikri, Z. A., Ha, J.-M., Park, Y.-K., Lee, H., Suh, D. J., et al. (2019). Heteropolyacid Supported on Zr-Beta Zeolite as an Active Catalyst for One-Pot Transformation of Furfural to γ-valerolactone. Appl. Catal. B: Environ. 241, 588–597. doi:10.1016/j.apcatb.2018.09.031

CrossRef Full Text | Google Scholar

Wu, H., Dai, W., Saravanamurugan, S., Li, H., and Yang, S. (2020). Endogenous X-C O Species Enable Catalyst-free Formylation Prerequisite for CO2 Reductive Upgrading. Green. Chem.. 22, 5822–5832. doi:10.1039/d0gc02142c

CrossRef Full Text | Google Scholar

Wu, H., Liu, Y., Li, H., and Yang, S. (2018). Rapid and Efficient Conversion of Bio-Based Sugar to 5-hydroxymethylfurfural Using Amino-Acid Derived Catalysts. Energy Sourc. A: Recovery, Utilization, Environ. Effects 40, 2632–2639. doi:10.1080/15567036.2018.1505982

CrossRef Full Text | Google Scholar

Wu, H., Zhang, L.-L., Wang, J., Jiang, Y., Li, H., Sudarsanam, P., et al. (2021). Room-temperature Quasi-Catalytic Hydrogen Generation from Waste and Water. Green. Chem. 23, 7528–7533. doi:10.1039/d1gc02722k

CrossRef Full Text | Google Scholar

Wu, W., Li, Y., Li, H., Zhao, W., and Yang, S. (2018). Acid-Base Bifunctional Hf Nanohybrids Enable High Selectivity in the Catalytic Conversion of Ethyl Levulinate to γ-Valerolactone. Catalysts 8, 264. doi:10.3390/catal8070264

CrossRef Full Text | Google Scholar

Xiao, Z., Zhou, H., Hao, J., Hong, H., Song, Y., He, R., et al. (2017). A Novel and Highly Efficient Zr-Containing Catalyst Based on Humic Acids for the Conversion of Biomass-Derived Ethyl Levulinate into Gamma-Valerolactone. Fuel 193, 322–330. doi:10.1016/j.fuel.2016.12.072

CrossRef Full Text | Google Scholar

Xie, C., Song, J., Zhou, B., Hu, J., Zhang, Z., Zhang, P., et al. (2016). Porous Hafnium Phosphonate: Novel Heterogeneous Catalyst for Conversion of Levulinic Acid and Esters into γ-Valerolactone. ACS Sustain. Chem. Eng. 4, 6231–6236. doi:10.1021/acssuschemeng.6b02230

CrossRef Full Text | Google Scholar

Xie, Y., Li, F., Wang, J., Wang, R., Wang, H., Liu, X., et al. (2017). Catalytic Transfer Hydrogenation of Ethyl Levulinate to γ-valerolactone over a Novel Porous Zirconium Trimetaphosphate. Mol. Catal. 442, 107–114. doi:10.1016/j.mcat.2017.09.011

CrossRef Full Text | Google Scholar

Xue, Z., Jiang, J., Li, G., Zhao, W., Wang, J., and Mu, T. (2016). Zirconium-cyanuric Acid Coordination Polymer: Highly Efficient Catalyst for Conversion of Levulinic Acid to γ-valerolactone. Catal. Sci. Technol. 6, 5374–5379. doi:10.1039/c5cy02215k

CrossRef Full Text | Google Scholar

Yang, T., Li, H., He, J., Liu, Y., Zhao, W., Wang, Z., et al. (2017). Porous Ti/Zr Microspheres for Efficient Transfer Hydrogenation of Biobased Ethyl Levulinate to γ-Valerolactone. ACS Omega 2, 1047–1054. doi:10.1021/acsomega.6b00469

PubMed Abstract | CrossRef Full Text | Google Scholar

Yang, Y., Liu, Q., Li, D., Tan, J., Zhang, Q., Wang, C., et al. (2017). Selective Hydrodeoxygenation of 5-hydroxymethylfurfural to 2,5-dimethylfuran on Ru-MoOx/C Catalysts. RSC Adv. 7, 16311–16318. doi:10.1039/c7ra00605e

CrossRef Full Text | Google Scholar

Ye, L., Han, Y., Feng, J., and Lu, X. (2020). A Review about Gvl Production from Lignocellulose: Focusing on the Full Components Utilization. Ind. Crops Prod. 144, 112031. doi:10.1016/j.indcrop.2019.112031

CrossRef Full Text | Google Scholar

Yin, K., and Shen, Y. (2020). Theoretical Insights into CO2 Hydrogenation to HCOOH over FexZr1-xO2 Solid Solution Catalyst. Appl. Surf. Sci. 528, 146926. doi:10.1016/j.apsusc.2020.146926

CrossRef Full Text | Google Scholar

Yu, Z., Li, Z., Zhang, L., Zhu, K., Wu, H., Li, H., et al. (2021). A Substituent- and Temperature-Controllable NHC-Derived Zwitterionic Catalyst Enables CO2 Upgrading for High-Efficiency Construction of Formamides and Benzimidazoles. Green. Chem. 23, 5759–5765. doi:10.1039/d1gc01897c

CrossRef Full Text | Google Scholar

Yun, W.-C., Yang, M.-T., and Lin, K.-Y. A. (2019). Water-born Zirconium-Based Metal Organic Frameworks as green and Effective Catalysts for Catalytic Transfer Hydrogenation of Levulinic Acid to γ-valerolactone: Critical Roles of Modulators. J. Colloid Interf. Sci. 543, 52–63. doi:10.1016/j.jcis.2019.02.036

CrossRef Full Text | Google Scholar

Zantye, M. S., Arora, A., and Hasan, M. M. F. (2021). Renewable-integrated Flexible Carbon Capture: A Synergistic Path Forward to Clean Energy Future. Energ. Environ. Sci. 14, 3986–4008. doi:10.1039/d0ee03946b

CrossRef Full Text | Google Scholar

Zhang, B., Hao, J., Sha, Y., Zhou, H., Yang, K., Song, Y., et al. (2018). Utilization of lignite Derivatives to Construct Zr-Based Catalysts for the Conversion of Biomass-Derived Ethyl Levulinate. Fuel 217, 122–130. doi:10.1016/j.fuel.2017.12.064

CrossRef Full Text | Google Scholar

Zhang, H., Li, H., Wang, A., Xu, C., and Yang, S. (2020). Progress of Catalytic Valorization of Bio-Glycerol with Urea into Glycerol Carbonate as a Monomer for Polymeric Materials. Adv. Polym. Techn. 2020, 1, 17. doi:10.1155/2020/7207068

CrossRef Full Text | Google Scholar

Zhang, H., Nai, J., Yu, L., and Lou, X. W. (2017). Metal-organic-framework-based Materials as Platforms for Renewable Energy and Environmental Applications. Joule 1, 77–107. doi:10.1016/j.joule.2017.08.008

CrossRef Full Text | Google Scholar

Zhang, H., Yang, W., Roslan, I. I., Jaenicke, S., and Chuah, G.-K. (2019). A Combo Zr-HY and Al-HY Zeolite Catalysts for the One-Pot cascade Transformation of Biomass-Derived Furfural to γ-valerolactone. J. Catal. 375, 56–67. doi:10.1016/j.jcat.2019.05.020

CrossRef Full Text | Google Scholar

Zhang, H., Zhang, L.-L., Tan, X., Li, H., and Yang, S. (2021). Catalytic High-Yield Biodiesel Production from Fatty Acids and Non-food Oils over a Magnetically Separable Acid Nanosphere. Ind. Crops Prod. 173, 114126. doi:10.1016/j.indcrop.2021.114126

CrossRef Full Text | Google Scholar

Zhang, S., Liu, Y., Yang, S., and Li, H. (2021). Catalytic Upgrading of Bio‐Based 5‐Hydroxymethylfurfural to 2,5‐Dimethylfuran with Non‐Noble Metals, Energy Technol., 9. 2100653. doi:10.1002/ente.202100653

CrossRef Full Text | Google Scholar

Zhang, X., Han, M., Liu, G., Wang, G., Zhang, Y., Zhang, H., et al. (2019). Simultaneously High-Rate Furfural Hydrogenation and Oxidation Upgrading on Nanostructured Transition Metal Phosphides through Electrocatalytic Conversion at Ambient Conditions. Appl. Catal. B: Environ. 244, 899–908. doi:10.1016/j.apcatb.2018.12.025

CrossRef Full Text | Google Scholar

Zhou, P., and Zhang, Z. (2016). One-pot Catalytic Conversion of Carbohydrates into Furfural and 5-hydroxymethylfurfural. Catal. Sci. Technol. 6, 3694–3712. doi:10.1039/c6cy00384b

CrossRef Full Text | Google Scholar

Zhou, S., Dai, F., Chen, Y., Dang, C., Zhang, C., Liu, D., et al. (2019). Sustainable Hydrothermal Self-Assembly of Hafnium-Lignosulfonate Nanohybrids for Highly Efficient Reductive Upgrading of 5-hydroxymethylfurfural. Green. Chem. 21, 1421–1431. doi:10.1039/c8gc03710h

CrossRef Full Text | Google Scholar

Zhou, S., Dai, F., Xiang, Z., Song, T., Liu, D., Lu, F., et al. (2019). Zirconium-lignosulfonate Polyphenolic Polymer for Highly Efficient Hydrogen Transfer of Biomass-Derived Oxygenates under Mild Conditions. Appl. Catal. B: Environ. 248, 31–43. doi:10.1016/j.apcatb.2019.02.011

CrossRef Full Text | Google Scholar

Zhu, Y., Li, Z., and Chen, J. (2019). Applications of Lignin-Derived Catalysts for green Synthesis. Green. Energ. Environ. 4, 210–244. doi:10.1016/j.gee.2019.01.003

CrossRef Full Text | Google Scholar

Zhu, Y., Liu, S., Jaenicke, S., and Chuah, G. (2004). Zirconia Catalysts in Meerwein-Ponndorf-Verley Reduction of Citral. Catal. Today 97, 249–255. doi:10.1016/j.cattod.2004.07.002

CrossRef Full Text | Google Scholar