This article is a correction to:
Accuracy of the Horizontal Calibrator in Correcting Leg Length and Restoring Femoral Offset in Total Hip Arthroplasty
Xing Chen
Shuxing Xing1
Huisheng Wang
Xizhuang Bai
Xi Li- 1Department of Orthopedic Surgery, Chengdu Fifth People’s Hospital, The Fifth People’s Hospital of Chengdu University of TCM, Chengdu, China
- 2Department of Orthopedics and Sports Medicine and Joint Surgery, Liaoning Provincial People’s Hospital, People92s Hospital of China Medical University, Shenyang, China
A Corrigendum on
Accuracy of the Horizontal Calibrator in Correcting Leg Length and Restoring Femoral Offset in Total Hip Arthroplasty
by Chen X., Xing S., Zhu Z., Wang H., Yu Z., Bai X., et al. (2022). Front. Surg. 9:845364. doi: 10.3389/fsurg.2022.845364
1. In the original article, there was an error in “MATERIALS AND METHODS “ section, “Measuring Technique” sub-section, Paragraph one, Line 10–12 : “OD is measured by the distance between the axis of femur and the center of the femoral head (Figures 1, 2) (1, 12).”
FIGURE 1
Figure 1.
FIGURE 2
Figure 2.
A correction has been made to “MATERIALS AND METHODS “ section, “Measuring Technique” sub-section, Paragraph one, Line 10–12 : “OD is measured by the distance between the axis of femur and the center of the femoral head (Figure 1) (1, 12).”
2. In the original article, there was an error in “RESULTS “ section, Paragraph one, Line 24–26 : “Independent t-test data of the two groups (p < 0.001; 95% CI = −5.1, −2.2) showed statistical significance (Figure 5).”
FIGURE 5
Figure 5.
A correction has been made to “RESULTS “section, Paragraph one, Line 24–26 : “Independent t-test data of the two groups (p < 0.001; 95% CI = −5.1, −2.2) showed statistical significance (Figure 2).”
3. In the original article, there was a mistake in the legend for “FIGURE 4” as published : “Physical diagram of the horizontal calibrator. (a) Shows all the components of the horizontal calibrator. See Figure 2 for details. (b) Shows the complete connected physical diagram of the horizontal calibrator, which was reserved preoperatively.”
FIGURE 4
Figure 4.
The correct legend appears below:
“Physical diagram of the horizontal calibrator. (a) Shows all the components of the horizontal calibrator. See Figure 3 for details. (b) Shows the complete connected physical diagram of the horizontal calibrator, which was reserved preoperatively.”
FIGURE 3
Figure 3.
The authors apologize for these errors and state that these do not change the scientific conclusions of the article in any way. The original article has been updated.
Conflict of Interest
The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest.
Publisher's Note
All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article, or claim that may be made by its manufacturer, is not guaranteed or endorsed by the publisher.
Keywords: hip arthroplasty, leg length discrepancy, offset, intraoperative, calibrator
Citation: Chen X, Xing S, Zhu Z, Wang H, Yu Z, Bai X and Li X (2022) Corrigendum: Accuracy of the Horizontal Calibrator in Correcting Leg Length and Restoring Femoral Offset in Total Hip Arthroplasty. Front. Surg. 9:890691. doi: 10.3389/fsurg.2022.890691
Received: 6 March 2022; Accepted: 19 May 2022;
Published: 4 August 2022.
Edited by:
Frontiers in Surgery Editorial Office, Frontiers Media SA, Switzerland*Correspondence: Xi Li bGl4aXNla2lAZ21haWwuY29t
Specialty section: This article was submitted to Orthopedic Surgery, a section of the journal Frontiers in Surgery
Copyright © 2022 Chen, Xing, Zhu, Wang, Yu, Bai and Li. This is an open-access article distributed under the terms of the Creative Commons Attribution License (CC BY). The use, distribution or reproduction in other forums is permitted, provided the original author(s) and the copyright owner(s) are credited and that the original publication in this journal is cited, in accordance with accepted academic practice. No use, distribution or reproduction is permitted which does not comply with these terms.