Multifunctional Cellulose and Cellulose-Based (Nano) Composite Adsorbents

In recent years, faced with the improvement of environmental quality problems, cellulose and cellulose-based (nano) composites have attracted great attention as adsorbents. In this review article, we first report the recent progress of modification and functionalization of cellulose adsorbents. In addition, the adsorbents produced by the modification and functionalization of carboxymehyl cellulose are also introduced. Moreover, the cellulose-based (nano) composites as adsorbents are reviewed in detail. Finally, the development prospect of cellulose and cellulose-based (nano) composites is studied in the field of the environment. In this review article, a critical comment is given based on our knowledge. It is believed that these biomass adsorbents will play an increasingly important role in the field of the environment.

Introduction

In recent years, many environmental problems have attracted more and more attention because they are related to human survival and development (Jarup and Akesson, 2009). Heavy metals ions and organic pollutants play an important role in human health, disturbing the normal growth of plants and damaging the ecological balance (Heppner et al., 2009). Some heavy metals ions and organic pollutants are teratogenic, mutagenic, and carcinogenic substances. There is no doubt that heavy metals ions and organic pollutants accumulate in the environment and biological energy is enriched through the food chain. Therefore, it is very important to remove these pollutants using adsorbents from wastewater (Chen et al., 2015).

It is believed that lignocellulose is an important renewable biomass, consisting of cellulose, hemicelluloses, and lignin, which is used as feedstock to fabricate bio-based fuels, chemicals, and materials (Menon and Rao, 2012; Huang et al., 2018; Dong H. et al., 2020; Huang et al., 2021b). Cellulose is a polysaccharide composed of glucose molecules and the most abundant renewable biomass in the world. Cellulose is the main component of the plant cell wall. It is expected that the conversion of bio-ethanol from cellulose will be a clean energy technology, replacing the traditional grain ethanol technology to meet global energy demand (Asgher et al., 2013). However, it is still difficult to achieve large-scale industrialization due to the pretreatment of raw materials and the high cost of cellulose (Mansfield et al., 1999). Therefore, bio-based chemicals and materials produced from cellulose are expected to be beneficial to the application of cellulose (Nzediegwu and Dumont, 2021). It is believed that bio-based materials produced from cellulose have become the main research focus of academia (Klemm et al., 2005; Li et al., 2011; Liu et al., 2017; Cao et al., 2018). In addition, carboxymehyl cellulose is an organic substance, a carboxymethylated derivative of cellulose, which is easy to disperse in water to form a transparent colloidal solution.

It is well known that adsorption is considered to be an economic route to remove heavy metals ions and organic pollutants from wastewater (Yagub et al., 2014). In addition, the adsorbent could be reused through an appropriate desorption and regeneration process. Activated carbon adsorbents are widely used to remove heavy metal pollutants due to their large pore volume and high surface area (Mohan and Pittman, 2006; Liu et al., 2018; Liu et al., 2019). To date, hundreds of adsorbents have been reported in the literature (Babel and Kurniawan, 2003; Crini, 2006). The cellulose and cellulose-based (nano) composites have different compositions, structures, and properties, compared with activated carbon adsorbent. It is believed that bio-sorption of agricultural wastes, by-products, and natural substances is a promising and emerging adsorbent method for the treatment of heavy metals ions and organic pollutants due to its high efficiency and wide sources (Volesky and Holan, 1995; O'Connell et al., 2008).

Herein, this review article introduces the application of cellulose and cellulose-based (nano) composites in the removal of heavy metals ions and organic pollutants from wastewater. The adsorbents produced by modification and functionalization of cellulose, carboxymehyl cellulose, and cellulose-based (nano) composites are reviewed. In addition, the adsorption mechanism is briefly discussed. Finally, we try to put forward the possible future development of cellulose and cellulose-based materials in the field of the environment.

Adsorbents Produced by Modification and Functionalization of Cellulose

Heavy metals ions and organic pollutants are the main factors causing wastewater pollution. The modification and functionalization of cellulose are usually utilized to create adsorbents to remove heavy metals ions. In early 2001, Liu’s group did pioneering work (Liu et al., 2001). They developed spherical cellulose as an adsorbent to remove and recover Cr³⁺ with a recovery rate of approximately 85.2%, following the predominant complex adsorption mechanism. It is reported that the adsorption of Cr³⁺ ions by an adsorbent depends on time, concentration, pH, and temperature. Then, Xu et al. (2002) also reported the removal of Cd²⁺ by immobilized cellulose-binding domains synthetic phytochelatin bio-adsorbents at the level of per million. Shukla and Pai (2005) assessed the cellulose-containing biomass for Pb²⁺ removal. The results showed the maximum cation uptake value of 0.127 mmol g⁻¹ for coir, 0.087 mmol g⁻¹ for sawdust, 0.090 mmol g⁻¹ for jute, and 0.106 mmol g⁻¹ for groundnut shell. Acrylonitrile-grafted cyanoethyl cellulose was also formed from cyanoethyl cellulose by the ionic-xanthate method to graft the acrylonitrile (Kamel et al., 2006). Undoubtedly, these early works showed that the modification and functionalization of cellulose is a promising bio-adsorbent method to remove heavy metals ions. After that, more and more research groups have paid more attention to the synthesis, properties, and application potential of bio-adsorbents.

O'Connell et al. (2006b) produced a regenerated cellulose adsorbent. It was found that glycidyl methacrylate-modified cellulose could remove 72 mg g⁻¹ of Pb²⁺ ions from aqueous solution at 23°C. In addition, the adsorbent was also applied to remove Ni²⁺ ions from an aqueous solution with approximately 48 mg g⁻¹ removed (O'Connell et al., 2006a). It should be pointed out, however, that there are still some debates about the function of cellulose. Garcia-Reyes and Rangel-Mendez (2009) demonstrated that hemicellulose and lignin were the main contributors for the removal of Cr³⁺ in aqueous solution, while cellulose did not seem to be involved. Recently, a microcrystalline cellulose (MCC) adsorbent was used to remove Pb²⁺ ions from aqueous solution with 1,2,3,4-butanetetracarboxylic acid (Hashem et al., 2020). According to the Langmuir theory, the maximum adsorption capacity was 1,155 mg g⁻¹ at pH 5 and 30°C. The pseudo-second order kinetic model indicated the chemisorption in the adsorption process due to the high density of active sites. It observed the endothermic and nonspontaneous adsorption of Pb²⁺ ions by MCC.

Cadmium, a typical heavy metal, has the characteristics of high fat solubility, bioaccumulation, and toxicity, contributing to wastewater pollution. Belhalfaoui and co-workers chemically modified cellulose with succinic anhydride in toluene to obtain succinylated cellulose (Belhalfaoui et al., 2009). Sodium succinylated cellulose displayed high sorption efficiency and high selectivity to remove Cd²⁺ with a maximum uptake of 185.2 mg g⁻¹ for distilled water and 178.6 mg g⁻¹ for spiked groundwater solutions. It suggested that active functional groups played a major role in metal sorption. It followed an ion-exchange mechanism in the removal process. We would like to point out that this work provided a very valuable example for the research of adsorption mechanisms. In Lu’s work, the different adsorption capacities from Langmuir-Freundlich were carried out using lawny grass modified by citric acid as an adsorbent to remove Cd²⁺ from aqueous solution (Lu et al., 2010).

In the literature, the modification and functionalization of cellulose were also applied to absorb toxic and radioactive elements such as Hg²⁺, UO₂²⁺, Th⁴⁺, and arsenate anions. It also reported that 95.5% alpha-cellulose grafting with acrylamide was utilized as an adsorbent to remove Hg²⁺ ions with an adsorption capacity of 625 mg g⁻¹ (Hashem et al., 2006). Takagai et al. (2011) investigated different thio-modified cellulose resins to remove Hg²⁺ ions in acidic solutions. Furthermore, three silylcellulosic derivatives of cellulose, trimethylsilyl-cellulose, and triphenylsilyl-cellulose with different substitution degrees were examined as sorbents for uranyl ions in wastewaters. The results revealed that the complexation of cellulose and trimethylsilyl-cellulose with UO₂²⁺ improved the thermal stability (Bontea et al., 2006). Anirudhan and Rejeena (2011) synthesized a tannin-modified poly (glycidylmethacrylate)- grafted zirconium oxide-densified cellulose adsorbent. The procedure adopted for the preparation of the adsorbent is presented in Figure 1. The authors indicated that the pH was found to be 5.5 with the adsorption rate of 99.2% for Th⁴⁺. Moreover, an Fe³⁺-loaded ligand exchange cotton cellulose macroporous bead adsorbent was applied for selective adsorption of arsenate anions by Zhao et al. (2009). The cellulose nanofibrils (CNFs) were reported to have various applications (Cao et al., 2019; Cao et al., 2020; Huang et al., 2020; Wang P. et al., 2020). More recently, CNFs were used to adsorb Hg²⁺ ions in an aqueous solution (Bisla et al., 2020). Modified CNFs had an adsorption capacity of 131.86 mg g⁻¹ for Hg²⁺ ions. The pseudo-second order kinetic model implied chemisorption during the removal of Hg²⁺ ions from simulated wastewater. The diethylenetriaminepentaacetic acid-modified cellulose was obtained by a pre-grafting technique (Li et al., 2021). The adsorbent showed an ultrahigh adsorption capacity of 443.8 mg g⁻¹ for Hg²⁺ in aqueous solution. A total of 88.13% of the original adsorption capacity was maintained after five cycles of the regeneration process. Aminotriazole isomer-modified cellulose microspheres with high nitrogen content showed potential affinity for U⁶⁺ (Wen et al., 2021). The microspheres possessed good adsorption capacity, selectivity, and reusability for U⁶⁺. It removed 99.45% from uranium contaminated water, 21.68% from contaminated groundwater, and 75.97% from simulated seawater.

FIGURE 1

FIGURE 1. Proposed reaction mechanism for the synthesis of tannin-modified poly (glycidylmethacrylate)-grafted zirconium oxide densified cellulose (TMPGZDC): zirconium oxide densified cellulose (ZDC) grafted with glycidylmethacrylate (GMA), N,N0-methylenebisacrylamide (MBA), and poly (glycidylmethacrylate)-grafted zirconium oxide densified cellulose (PGZDC) (Anirudhan and Rejeena, 2011).

Generally, the modification and functionalization of cellulose can remove all kinds of heavy metals ions simultaneously. In fact, wastewater contains a variety of heavy metals ions. There are some reports about this type of research. For example, Guclu et al. (2003) found four types of cellulose graft copolymers that removed Pb²⁺, Cu²⁺, and Cd²⁺ ions from aqueous solution. Cellulosic materials containing grafted polyacrylonitrile and poly (acrylic acid) molecules were also reported to remove Cd²⁺ and Cu²⁺ ions from aqueous solutions (Okieimen et al., 2005). Norkus et al. (2006) applied an oxygen delignified alkaline cellulose pulp slurry to remove Fe, Mn, and Cu. The maximum adsorption capacities of Ni²⁺, Co²⁺, Zn²⁺, and Cd²⁺ were 1.28, 1.23, 1.21, and 1.13 mol kg⁻¹ by using chemically modified orange peel cellulose adsorbents, which increased by 95, 178, 60, and 130%, respectively, compared with that of raw orange peel (Li et al., 2008). The modified sugarcane bagasse and chemically modified cellulose displayed adsorption capacities for Ca²⁺ from 15.6 to 54.1 mg g⁻¹ and Mg²⁺ from 13.5 to 42.6 mg g⁻¹ (Karnitz et al., 2010). Recently, modified cellulose hydrogels were reported for the adsorption of heavy metals ions by the ion-exchange mechanism (Zhao et al., 2019). The maximum absorption capacity of 157.51, 393.28, and 289.97 mg g⁻¹ for Cu²⁺, Pb²⁺, and Cd²⁺ ions was found in modified cellulose hydrogels, respectively. The thiol-functionalized cellulose nanofiber membrane was reported to adsorb heavy metals ions by chemisorption (Choi et al., 2020). It achieved adsorption capacities of 49.0 mg g⁻¹ for Cu²⁺, 45.9 mg g⁻¹ for Cd²⁺, and 22.0 mg g⁻¹ for Pb²⁺ in the Langmuir isotherm. The microwave-functionalized cellulose derived from rice husk was reported to eliminate Pb²⁺, Cd²⁺, and Ni²⁺ (Qu et al., 2020). It achieved adsorption capacities of 295.20 mg g⁻¹ for Pb²⁺, 151.51 mg g⁻¹ for Cd²⁺, and 72.80 mg g⁻¹ for Ni²⁺. The functionalized cellulose was found to have good recoverability and adsorption efficiency after five cycles.

Besides the removal of heavy metals ions, the modification and functionalization of cellulose are also applied to the removal of inorganic pollutants. Inukai et al. (2004) firstly used N-methylglucamine-type cellulose derivatives to remove B³⁺. Then, Fe³⁺-loaded ligand exchange cotton cellulose as a bead adsorbent was reported to remove fluoride from drinking water by Zhao et al. (2008). Anirudhan et al. (2009) synthesized a cellulose-based anion exchanger bearing the –N⁺HR₂Cl⁻ functional group with the adsorption capacity of 197.75 mg g⁻¹ for V⁵⁺ at 30°C. After that, they demonstrated that about 99.6% of phosphate was adsorbed in 180 min of contact at 100 mg L⁻¹ by using a cellulose-grafted epichlorohydrin functionalized polyethylenimine graft copolymer as an adsorbent (Anirudhan et al., 2012). Besides the removal of heavy metals ions, it is also important for the modification and functionalization of cellulose to remove organic pollutants. For example, Fang et al. (2004) prepared a lysine-cellulose bead adsorbent for removing bacterial endotoxins. The adsorbent had the characteristics of mechanical strength, blood compatibility, and cytotoxicity. Alila and Boufi (2009) constructed a modified cellulose fiber adsorbent to remove several aromatic organic compounds and three herbicides of Alachlor, Linuron, and Atrazine. More recently, a cellulose acetate fiber membrane was reported to remove methylene blue (MB) and Congo red (CR) dyes (Chen et al., 2020). It was observed that the adsorption capacities were 69.89 mg g⁻¹ for MB and 67.31 mg g⁻¹ for CR. An anionic cellulose foam was obtained by grafting and chemical crosslinking (Feng et al., 2020). It exhibited an adsorption capacity of 364.22 mg g⁻¹ for anionic dye Eosin Y and a removal efficiency of 99.58%. The chemical and monolayer action anionic dyes were suggested during the adsorption procedure.

There have been many reports about the removal of lipoprotein by modification and functionalization of cellulose. As early as 1988, Franceschini et al. (1988) comparatively tested a dextran sulfate cellulose column and double membrane filtration for the extracorporeal removal of low density lipoproteins. Schulzeck et al. (1992) further discovered five patients with familial hypercholesterolemia and diet- and drug-resistant low-density lipoprotein cholesterol greater than 230 mg dl⁻¹ using dextran sulfate cellulose adsorption. Olbricht (1996) indicated the extracorporeal removal of low-density lipoprotein cholesterol by dextran sulfate cellulose adsorption. It reported that the reduction in cholesterol per treatment was 65–75% and in most patients one treatment per week was sufficient to reduce cholesterol to 100–150 mg dl⁻¹. In Wang’s work, a cellulose adsorbent with amphiphilic ligands was applied to adsorb low-density lipoprotein with a better selectivity and adsorption capacity for the removal of low density lipoprotein (LDL), total cholesterol (TC), total proteins (TP) at 0.857, 1.317, and 1.002 mg ml⁻¹, respectively (Wang et al., 2002). The adsorbent showed quite good adsorption performance for selective removal of LDL from human plasma (Yu et al., 2006). Wang et al. (2006) synthesized a carboxyl modified polyethylene glycol (PEG) spacer and linked it covalently to cellulose beads. Both the adsorption capacity and adsorption efficiency of the ligand was increased for adsorption of LDL-cholesterol and the average adsorption capacity of LDL-cholesterol was increased to 0.903 mg ml⁻¹.

Beutler and Gelbart (1986) reported that cellulose columns efficiently removed leukocytes from whole blood, and the leukocyte removal activity of cellulose columns was due to mechanical filtration. Weber et al. (1995) produced regenerated cellulose (RC) of 1–8 μm modified with polyethyleneimine or diethylaminoethyl groups. RC had high adsorption capacity for endotoxins in human plasma. Butnaru et al. (2003) discussed the treatment of wastewater from cellulose dyeing with direct dyes by electro-coagulation. A cellulose microporous hollow fiber membrane was applied for the dispersion-free reactive extraction of thiol compounds (Yang et al., 2007). Greben et al. (2007) demonstrated that salinity (sulphate) could be removed using the fermentation products of grass-cellulose. The polycation-immobilized pore cellulose spherical particles were also reported to remove the endotoxin by Sakata et al. (2007).

Zhang and Akbulut (2011) investigated the adsorption, desorption, and removal behavior of polymeric nanoparticulate drug delivery systems (PNDDS). Figure 2A shows the unimodal and relatively narrow intensity-weighted particle size distribution of PNDDS. It obtained six different particle size distributions of 46 ± 1, 81 ± 2, 159 ± 1, 197 ± 4, 238 ± 7, and 271 ± 2 nm. Based on TEM images, they observed core-shell spherical PNDDS (Figures 2B,C). The size had an effect on the adsorption, desorption, and removal of polymeric nanomedicine. Experimental results indicated that the removal rate of the particles increased with the increased particle size. More recently, a cross-linked cellulose aerogel from rice straw with a density of 2.2–24 mg cm⁻³ and porosity of 98.4–99.8% was achieved by a freeze-drying process (Dilamian and Noroozi, 2021). Different shapes of two types of dilute cellulose suspensions were found. The aerogels had a specific area of 178.8 m² g⁻¹ and mesopore volume of 0.8 cm³ g⁻¹. It achieved adsorption capacities up to 170 g g⁻¹ for the super-hydrophobic and oleophilic cellulose aerogels. A cellulose-rich modified rice husk was also reported for the removal of MB and Al³⁺ (You et al., 2021). It carried out the uptake for MB of 50.15 mg g⁻¹ and the uptake for Al³⁺ of 2.87 mg g⁻¹. Authors suggested this was due to the adsorption mechanisms of MB including pore filling, π-π interaction, and electrostatic attraction, as well as the adsorption mechanisms of Al³⁺, such as surface complexation, n-π interaction, and ion exchange. The functionalization of cellulose with hyperbranched polyamide was prepared for adsorption of orange II (OT) and Cu²⁺ ions (Yu et al., 2019). It achieved maximum sorption capacities of 976 mg g⁻¹ for OT and 138 mg g⁻¹ for Cu²⁺ ions. Authors indicated an electrostatic interaction for OT adsorption and the complexation/chelation of Cu²⁺ adsorption.

FIGURE 2

FIGURE 2. (A) Intensity-weighted particle size distributions for polymeric nanoparticulate drug delivery systems (PNDDS). The mean values of Z-average sizes of different batches of PNDDS were 46 ± 1 nm (black, A), 81 ± 2 nm (red, B), 159 ± 1 nm (cyan, C), 197 ± 4 nm (magenta, D), 238 ± 7 nm (dark yellow, E), and 271 ± 2 nm (orange, F). TEM micrographs for (B) 46 nm PNDDS and (C) 271 nm PNDDS described in a dynamic light scattering (DLS) study (Zhang and Akbulut, 2011).

Adsorbents Produced by Modification and Functionalization of Carboxymehyl Cellulose

Carboxymehyl cellulose (CMC) is the carboxymehyl group-substituted product of cellulose. CMC has the characteristics of high viscosity, adhesion, acid resistance, and physiological harm, which is widely used in food, medicine, papermaking, and textiles. According to the reports in the literature, it should be pointed out that the modification and functionalization of CMC are widely applied to remove heavy metals ions and organic pollutants. Bacterial cellulose (BC) was found to have important application potential (Ma et al., 2021; Mai et al., 2021; Wang X. et al., 2021; Guo et al., 2022). The early work had been done by Cavus et al. (2006). They developed a crosslinked hydroxyethyl cellulose-g-poly (acrylic acid) graft copolymer to remove Pb²⁺, Cu²⁺, and Cd²⁺. In Chen’s work, it was reported that carboxymethylated-BC performed better adsorption with values of 12.63 mg g⁻¹ (copper) and 60.42 mg g⁻¹ (lead) (Chen et al., 2009), compared with the values of 9.67 mg g⁻¹ (copper) and 22.56 mg g⁻¹ (lead) of BC. Obviously, carboxymethylated-BC had better adsorption performance. They demonstrated the pseudo-second-order kinetic model and the Langmuir model. Yang et al. (2011) applied CMC hydrogel beads with the maximum adsorption capacity of 6.49, 4.06, and 5.15 mmoL g⁻¹ for Cu²⁺, Ni²⁺, and Pb²⁺, respectively. Ali (2012) discovered that the CMC and 2-acrylamido-2-methyl propane sulfonic acid hydrogels showed a great capability and were reused at least five times to recover toxic metal ions such as Mn²⁺, Co²⁺, Cu²⁺, and Fe³⁺ from their aqueous solutions. Undoubtedly, the modification and functionalization of CMC displayed amazing absorption capacity for various heavy metals ions. The cellulose acetate/sulfonated poly (ether ketone) blend ultrafiltration membranes were applied for the separation of Cr³⁺ ions from aqueous streams by ultrafiltration processes (Arthanareeswaran et al., 2007a). Dewangan et al. (2011) also developed the removal of Cr⁶⁺ by adsorption beads of sodium alginate and CMC.

There are also some reports on the removal of individual metal ions. For example, the removal of arsenic ions was reported using a crosslinked sodium alginate/CMC adsorbent (Tiwari et al., 2008). Shao et al. (2009) developed the application of CMC grafted multiwalled carbon nanotubes (MWCNT-g-CMC) by using plasma techniques in the removal of UO₂²⁺ from the aqueous solution, which had much higher sorption capacity than raw MWCNT. It obtained the sorption capacity of 6.0 × 10^–5 mol/g for raw MWCNT, 1.1 × 10^–4 mol/g for MWCNT-treat, and 4.7 × 10^–4 mol/g for MWCNT-g-CMC (Figure 3A). MWCNT-g-CMC displayed a sorption percentage of UO₂²⁺ from ∼23% to ∼98% with the increasing MWCNT-g-CMC content from 0.10 to 1.0 g/L (Figure 3B). Zhang et al. (2010) demonstrated that the carboxylate-functionalized cellulose possessed excellent adsorption capacity of 84.4% for Pb²⁺, which was significantly higher than that of unmodified cellulose. These examples further implied that modification and functionalization improved the adsorption performance. The ethylenediaminetetraacetic acid-functionalized magnetic Fe₃O₄ chitosan oligosaccharide and CMC nanocomposite adsorbent was fabricated for Pb²⁺ adsorption (Lian et al., 2020). The adsorption capacity for monolayer chemical adsorption was 432.34 mg g⁻¹. The nanocomposite exhibited a Pb²⁺ removal rate of ∼100% using metal ion solutions of 100 and 200 mg L⁻¹.

FIGURE 3

FIGURE 3. Sorption isotherms (A) and effect of sorbent content (B) on the removal of UO₂²⁺ from solution on raw MWCNT, on MWCNT-treat, and on MWCNT-g-CMC. T = 25 ± 2°C, equilibrium time 24 h, pH = 5.0 ± 0.1, C [NaClO₄] = 1.0 × 10^‒2 mol/L (A) m/V = 0.4 g/L, (B) C [UO₂²⁺]_(initial) = 2.00 × 10^‒4 mol/L (Shao et al., 2009).

As mentioned above, it is very important to remove organic pollutants from wastewater. Ghanta et al. (2005) applied cellulose acetate blend and aromatic polyamide hydrazide reverse osmosis membranes for their separation behavior of phenol from phenol-water mixtures. Then, Eberhardt et al. (2006) reported the removal of (ortho) phosphate by refined aspen wood fiber treated with CMC and ferrous chloride. After that, De Smet’s group developed a super-flux cellulose triacetate dialyzer membrane to remove non-protein-bound and protein-bound uremic solutes (De Smet et al., 2007). The application of a microporous cationic hydrogel of hydroxypropyl cellulose in the removal of anionic dye was carried out by Yan et al. (2009). It was found that the adsorbent displayed an adsorption capacity of 2,478 g kg⁻¹ for anionic dye AO7 at pH 3.96. Bodalo et al. (2005) reported the behavior of cellulose acetate membranes by reverse osmosis of ammonium aqueous solutions. The modification and functionalization of CMC also had the ability to remove protein. Metal ion separation and protein removal were also investigated using modified cellulose acetate membranes by Arthanareeswaran et al. (2007b). The millimeter-sized chitosan/CMC hollow capsules were prepared to remove three typical dyes such as MB, methyl orange (MO), and acid blue-113 (AB) by mixing and stirring positively charged chitosan and negatively charged CMC solutions under an electrostatic interaction (Kong et al., 2020). They achieved removal capacities of 64.6 mg g⁻¹ for MB, 334.8 mg g⁻¹ for MO, and 526.8 mg g⁻¹ for AB. CMC/carboxylated graphene oxide composite microbeads were achieved to remove cationic MB dye (Eltaweil et al., 2020). They had an adsorption capacity of 180.32 mg g⁻¹. The adsorbent had better reusability for nine cycles with improved adsorption properties. More recently, Mai et al. (2021) applied an in situ anchoring method to prepare zeolitic imidazolate frameworks (ZIFs)@carboxymethylated bacterial cellulose (ZCMBC) composite films (Figure 4). The ZCMBC composite films were reported to have a high ZIFs loading rate and satisfactory selective indigo carmine removal efficiency (98.7%). The authors suggested the adsorption mechanism of IC⁻ by ZCMBC composite films (Figure 5).

FIGURE 4

FIGURE 4. Schematic illustration of the synthesis of ZCMBC composite films (Mai et al., 2021).

FIGURE 5

FIGURE 5. Proposed schematic diagram for adsorption mechanism of IC⁻ by ZCMBC composite films. The atoms are colored as follows: carbon (black), sulfur (earthy yellow), oxygen (red), zinc (light blue), cobalt (pink), sodium (wine red), hydrogen (grey), and nitrogen (dark blue). The light purple sphere indicates the cavity of ZnZIF-67 (Mai et al., 2021).

Millimeter hollow CMC microspheres/poly (ethyleneimine) (PEI) microspheres were fabricated for dye adsorption (Yang et al., 2021). The hollow microspheres had an adsorption capacity of 452 mg g⁻¹ for MB. CMC and genipin crosslinked carboxyalkyl-chitosan combined with a sulfonated graphene oxide sponge with multiple active sites was fabricated for adsorbing sulfonamide antibiotics (Liu Y. et al., 2021). The composite showed high sulfamethoxazole and sulfapyridine. It obtained an adsorption capacity of 312.28 mg g⁻¹ for sulfamethoxazole and 161.89 mg g⁻¹ for sulfapyridine at 298 K. CTAB-modified CMC/bagasse cryogels were reported to remove bisphenol A (BPA), MB, and Cr⁶⁺ ions in binary or ternary aqueous mixtures (Meneses et al., 2022). They exhibited a removal rate of 100% for MB, 70% for Cr⁶⁺, and 95% for BPA. They observed an increased adsorption capacity of Cr⁶⁺ ions in the binary mixture or ternary mixture due to the synergistic effect.

Adsorbents Produced by Cellulose-Based (Nano) Composites

It is known that (nano) composites are composed of two or more kinds of materials, which have synergistic effects and new properties, compared with an individual component. It means that cellulose-based (nano) composites were fabricated by using cellulose as the matrix and using inorganic or organic materials as reinforcement. In the literature, there are reports about the applications of cellulose-based (nano) composites. It is of great importance for cellulose-based (nano) composites adsorbents to remove heavy metals ions and organic pollutants. In early 2005, Guo and Chen (2005) completed pioneering work to remove heavy metals ions by using cellulose-based composites as adsorbents. They firstly applied cellulose/iron oxyhydroxide to remove arsenate and arsenite from groundwater. It was reported that the adsorbents displayed high removal efficiency of arsenite (99.6 mg g⁻¹) and arsenate (33.2 mg g⁻¹) at pH 7.0. They also summarized three reasons for and five advantages of cellulose/iron oxyhydroxide, such as cheap resources, recycled materials, excellent mechanical strength, high adsorption capacity, and high regeneration efficiency. Then, they used EXAFS to investigate the removal mechanism of cellulose/iron oxyhydroxide for arsenic (Guo et al., 2007). From then on, many groups explored the applications of cellulose-based (nano) composites in the removal of heavy metals ions and organic pollutants. For example, Maliyekkal et al. (2010) reported the applications for Pb²⁺ removal from aqueous solutions by using cellulose/manganese oxide nanocomposites. The physic-sorption played a dominant role in the adsorption of Pb²⁺. Nata et al. (2011) made amine-rich magnetite/BC nanocomposites by the solvothermal reaction. It was found that these nanocomposites displayed an adsorption capacity towards As⁵⁺ ions. Kumar et al. (2012) reported a cellulose-montmorillonite composite with an adsorption capacity of 22.2 mg g⁻¹ for the detoxification of Cr⁶⁺ ions from industrial wastewater by a column methodology. It should be noted that the composite was reused for 10 adsorption-desorption cycles.

It is worth noting that hydroxyapatite has an excellent ion-exchangeability. In 2008, Choi and Jeong (2008) applied a hydroxyapatite/cellulose composite to remove heavy metals in aqueous solution. Islam et al. (2011) evaluated the feasibility of cellulose/carbonated hydroxyapatite nanocomposites for As⁵⁺ removal with the adsorption capacity of 12.72 mg g⁻¹. Authors found the chemical process in the adsorption process. In the research of water treatment using adsorbents, it is very important to judge the chemisorption and/or physisorption process on the absorption mechanism. The above results indicated that cellulose/carbonated hydroxyapatite (nano) composites are promising adsorbents in the removal of heavy metals ions.

Similarly, cellulose-based (nano) composites including organic polymers are also applied in the removal of heavy metals ions. For example, Lima et al. (2005) developed chitosan/cellulose acetate film with an affinity for adsorbing copper. Highly porous adsorptive chitosan/cellulose acetate blend hollow fiber membranes were applied for copper ion removal in a batch adsorption mode (Liu and Bai, 2006). Cifci and Kaya (2010) used a poly (vinyl alcohol) (PVA)/cellulose membranes composite for metal removal from aqueous solutions.

There are a few reports about cellulose-based (nano) composites as adsorbents in the removal of organic pollutants. Cellulose acetate-supported Ni/Fe nanoparticles were first carried out to remove trichloroethylene from water by Wu and Ritchie (2006). Dridi-Dhaouadi et al. (2011) researched the sorption behavior of Pb²⁺ and C.I. acid yellow 44 on posidonia oceanica. Zhu et al. (2011) also applied magnetic cellulose/Fe₃O₄/activated carbon composites to remove CR. The nanocellulose hybrid containing polyhedral oligomeric silsesquioxane was also investigated to remove reactive dyes (Xie et al., 2011b). More recently, iron-based metal-organic framework@cellulose aerogels were obtained for CR dye adsorption by the in situ growing method (Huang et al., 2021a). It achieved an adsorption capacity of 280.3 mg g⁻¹. Lemon peel/MCC hydrogels with porous structure and surface roughness were obtained for MB adsorption by direct co-dissolving in 1-butyl-3-methylimidazolium chloride (BmimCl) (Dai et al., 2021). The introduction of lemon peel increased the porosity and improved the thermal stability of the hydrogels. It obtained the maximum adsorption capacity of 57.54 mg g⁻¹ for hydrogels.

The hollow cellulose/carbon nanotubes composite beads with aligned porous structure were fabricated by ice template and freeze-drying technology (Ding et al., 2021). All cellulose concentrations, pre-freeze temperatures, and voltages affected the hollow structure and diameter of the beads. Authors discovered the enhanced diameter of the beads with the increase of cellulose concentration, the different structure of beads at different pre-freeze temperatures, and the decreased diameter of beads with increased voltage. The composite showed good reusability, biodegradability, and an adsorption capacity of 285.71 mg g⁻¹. A polyaniline/dicarboxyl acid cellulose@graphene oxide (GO) composite was synthesized to remove the reactive brilliant red K-2G (Liu T. et al., 2021). It obtained an adsorption capacity of 447.0 mg g⁻¹ for the first scenario, and 729.0 mg g⁻¹ during the subsequent photocatalysis process. A graphene oxide/cellulose nanocrystals nanocomposite was obtained to remove MB (Zaman et al., 2020). It removed around 98% of MB in 135 min and the maximum adsorption capacity was 751.88 mg g⁻¹ Wang et al. (2022) also reported porous polydimethylsiloxane@wood sponge/MXene (PDMS@WSM) with outstanding compressibility and hydrophobic/lipophilic ability as a crude oil absorbent (Figure 6). The wood sponge consisted of cellulose by the removal of lignin and hemicellulose from natural wood. The PDMS@WSM had a maximum adsorption capacity of 11.2 × 10⁵ g m⁻³ due to the excellent Joule heating and photothermal conversion effect.

FIGURE 6

FIGURE 6. (A) Schematic illustration of Joule-heating and solar-heating PDMS@WSM to clean up and recover a viscous crude oil spill. (B) Schematic showing the synthesis process of the MXene nanosheet. (C) Schematic illustration of the fabrication of the wood sponge and PDMS@WSM (Wang et al., 2022).

In fact, organic solvent can also improve the adsorption capacity of cellulose. Musyoka et al. (2011) reported ethylenediamine-modified cellulose with adsorption capacities of 0.0136 mmol g⁻¹ for Cd²⁺ and 0.0179 mmol g⁻¹ for Pb²⁺ ions. Xie et al. (2011a) synthesized nanocellulose hybrid biosorbents for adsorbing copper and nickel ions in aqueous solution. Hierarchical pore UiO-66/nanocellulose aerogels were prepared by a self-crosslinking method (Wang et al., 2019). The composite aerogels had adsorption capacities of 71.7 mg g⁻¹ for anionic methyl orange and 51.8 mg g⁻¹ for cationic MB. TEMPO-CNC MWCN/GO composite films were reported with a partition coefficient of 872.266 ml g⁻¹ (Zheng et al., 2020). Porous cellulose/chitosan spheres were prepared to adsorb Cu²⁺ (Wittmar et al., 2020). They obtained a maximum adsorption capacity of 52.5 mg g⁻¹ due to the amino group in the chitosan unit. Park et al. (2020) prepared poly (acryloyl hydrazide)-grafted CNC particles for adsorption of Cr⁶⁺ by strong electrostatic, hydrogen bonding, and chelating interactions. The adsorbents exhibited a high Cr⁶⁺ adsorption capacity of ∼457.6 mg g⁻¹ by intra-particle diffusion resistance. CNC/iron oxide composites were prepared to remove arsenic (Dong F. et al., 2020). They obtained the maximal amount of 13.866 mg g⁻¹ for As³⁺ and 15.712 mg g⁻¹ for As⁵⁺. They exhibited chemical adsorption of monolayers. A TEMPO-oxidized CNF/magnetite was prepared to adsorb lead ions with a removal rate of 80% (Abou-Zeid et al., 2021). An MCC/magnesium sulfate hexahydrate (MCC/MH) composite adsorbent was used to adsorb heavy metal Co²⁺ ions (Wang R. et al., 2021). It obtained a removal rate of 97.67% and adsorption capacity of 153.84 mg g⁻¹. Dialdehyde cellulose/GO composites adsorbents with high carboxyl groups density, high surface area, and low crystallinity index were obtained in both heterogeneous and homogeneous systems (Wang Z. et al., 2020). The adsorbents showed the adsorption capacities of 74.2 mg g⁻¹ for Cu²⁺ and 91.7 mg g⁻¹ for Pb²⁺. CNF/PVA composite gel spheres with 1–3 mm were prepared for organic pollutants and heavy metals ions (Yi et al., 2022). The spheres showed adsorption properties for simulated pollutants, including Cu²⁺, phenol, and aniline in water. They achieved a maximum absorption capacity of 17.22 As³⁺ and 15.712 mg g⁻¹ for As⁵⁺ mmol g⁻¹ for Cu²⁺, 176.72 mg g⁻¹ for phenol, and 341.93 mg g⁻¹ for aniline. The composite spheres also had good absorption properties for petroleum ether, ethyl acetate, and toluene. A liquid nitrogen directional freezing method was used to prepare CNF/chitosan/montmorillonite aerogels for wastewater treatment (Rong et al., 2021). The aerogels had a homogeneous three-dimensional directional pore structure, good mechanical properties, good adsorption performance, and reusability. They exhibited an adsorption capacity of 181.92 mg g⁻¹ for Cu²⁺, 170.19 mg g⁻¹ for Pb²⁺, and 163.85 mg g⁻¹ for Cd²⁺.

Mechanism of Adsorption

As mentioned above, it seems that the mechanism of adsorption can be simply divided into physisorption and chemisorption. In fact, it is believed that there exists simultaneous physisorption and chemisorption. In the adsorption process of adsorbents, the main mechanism still needs to be determined. As described in the literature, the physical forces include Van der Waals forces, hydrophobicity, hydrogen bonds, polarity and steric interaction, dipole induced dipole interaction, and pep interaction. Generally, it is reported that physisorption has the characteristics of low adsorption heat, does not require activation energy, single or multi molecular layer adsorption, no structure change of adsorbed molecules, no form of new chemical bonds, and is reversible. For the chemisorption process, it is considered that the adsorption heat is approximately equal to the reaction heat. The adsorption force is similar to the chemical bond and much stronger than Van der Waals forces. Chemisorption, as a single molecular layer adsorption, is selective and can be described by the Langmuir isotherm. In addition, chemisorption displays irreversibility to temperature and pressure, which requires activation energy. At present, the adsorption mechanisms are researched by adsorption kinetics, adsorption isotherms (Langmuir isotherm and Freundlich isotherm), and thermodynamics, which could explain the problems of physisorption and chemisorption, monolayer and multilayer adsorption. Therefore, it is very important to determine the type of adsorption. First, it can be judged according to the value of adsorption heat. The value of chemisorption heat is similar to that of the chemical reaction. In general, the value of chemisorption heat ranges from 83,740 to 418,680 J mol⁻¹, while the value of physisorption heat is approximately 20,000 J mol⁻¹. Secondly, the effect of temperature on the adsorption rate should be explored in the near future. During the chemisorption process, the adsorption rate is an activated process, which increases with the increase of temperature. However, physisorption is not an activated process, which has a high adsorption rate even at low temperatures. One can judge the type of adsorption by different adsorption processes at different temperatures. In the research of adsorption, adsorption capacities, regeneration efficiency, and selectivity are important factors. Moreover, in view of the above mentioned physisorption and chemisorption, one can conclude that chemisorption may have a high adsorption capacity and good selectivity due to chemical properties. However, physisorption has poor selectivity, which depends on the characteristics of the adsorbents.

Although most groups have investigated the mechanism of the adsorption process, we still have to say that it is not enough. For example, the famous Langmuir isotherm is based on the following assumptions of the uniformity of adsorbent surface, monolayer adsorption, dynamic adsorption, without force between the adsorbate molecules, etc., The Langmuir adsorption isotherm can be used in the low pressure range. When the gas pressure is higher in the adsorbate, close to the saturation vapor pressure, the equation produces a deviation due to the condensation of the adsorbate in the micro capillary and no single molecule layer adsorption. As for the Freundlich isotherm, it is an empirical formula in a narrow pressure range. In the low pressure or high pressure region, it cannot obtain satisfactory experimental results. Therefore, it is necessary to combine the new measurement method with molecular dynamics simulation to explore the adsorption mechanism. In fact, we believe that the adsorption is a very complex process, and some adsorption processes also include a chemical reaction and ion-exchange. Understanding the adsorption mechanism is of great significance for the synthesis and application of adsorbents.

Future Perspectives

We believe that there is an increasing demand for environmentally friendly and economically friendly adsorbents in the field of water treatment. As discussed in this review article, cellulose is one of the polysaccharides composed of glucose molecules and the most abundant natural renewable biomass in the world. Undoubtedly, the modification and functionalization of cellulose and cellulose-based (nano) composites meet these requirements. Although there is a long road ahead for these applications, cellulose has a very bright future as an amazing and promising bio-adsorbent for wastewater treatment. More importantly, we expect that low-cost and greener bio-adsorbents will open a new window for the high value-added applications of cellulose, compared with other adsorbents. Besides heavy metals ions and organic pollutants, the modification and functionalization of cellulose and cellulose-based (nano) composites were also reported for protein adsorption (Zhao et al., 2021), drugs adsorption and release (Zhang et al., 2019), bilirubin (Wang Y. et al., 2021), carbon dioxide (CO₂) adsorption (Sepahvand et al., 2020), and lysozymes (Rahmatika et al., 2020).

As described by Ali et al. (2012), there are many issues that need to be solved in the next step, such as adsorption mechanism, industrial scales preparation, regeneration, specific surface area, the management of removed pollutants, dispersion, etc., We would like to point out that there are many requirements for adsorbents in wastewater treatment, such as inexpensive, eco-friendly, environmentally friendly, good selectivity, high adsorption capacities, good regeneration efficiency, broad spectrum, etc., As we all know, it is difficult to obtain perfect adsorbents. Therefore, finding a balance among all factors is very important for practical applications.

The adsorbents are expected to have practical applications, which is the first and only standard to measure the quality of adsorbents. It is necessary to investigate the mechanism and eliminate interference at lab-scale batch studies. Obviously, unlike lab-scale batch studies, industrial waste water containing various heavy metals ions and organic pollutants is more complex. Sometimes, it was found that the adsorbents displayed good performance at lab studies and poor performance in industrial wastewater. At least, the absorbent with good performance at lab studies should be characterized and tested with industrial wastewater. So, the design of adsorbents should be based on realistic industrial applications, not the opposite. As described above, hundreds of cellulose-based bio-adsorbents were reported in the literature. However, few types of bio-adsorbents can be used in practical applications. The modification and functionalization of cellulose, CMC, and cellulose-based (nano) composites could be used to create bio-adsorbents to remove heavy metals ions and organic pollutants. The future development direction is put forward from the aspects of adsorption mechanism, theoretical simulation, and experimental verification. Although there is no common standard to judge these bio-adsorbents, it is necessary to narrow the scope.

In addition, it is worth noting that the main components of biomass are polysaccharides (cellulose and hemicellulose) and lignin. Cellulose is obtained by pretreatment of biomass. It seems that the development of pretreatment methods on biomass is of great importance to broaden its industrial applications. Obviously, the pretreatment methods determine whether cellulose and cellulose-based (nano) composites are economically friendly adsorbents. In general, cellulose can be used as a raw material to produce bio-based fuels, chemicals, and materials. Therefore, cellulose-based bio-adsorbents should have high value-added and low price capabilities, compared with other applications such as bio-based fuels, chemicals, and materials. Of course, the high regeneration efficiency of bio-adsorbents would contribute to reduce the cost.

Moreover, science and technology are like brothers. The problems of the adsorption mechanism, preparation, property, etc., may belong to the scientific field. However, the application in the wastewater field may belong to the technical field. It is found that the problems of technology always determine the quality and price of bio-adsorbents in the industrial process. So, there is still a long way to go from lab-scale batch studies to large-scale industrial applications of bio-adsorbents. We would like to point out that the research in the lab should meet industrial applications and resolve industrial problems, not the opposite.

Conclusion

In this review article, we summarized the recent progress of adsorbents produced by modification and functionalization of cellulose and cellulose-based (nano) composites to remove heavy metals ions and organic pollutants. We believe that the modification and functionalization of cellulose, carboxymehyl cellulose, and cellulose-based (nano) composites are amazing and promising methods to create bio-adsorbents in the field of water treatment. It is expected that cellulose and cellulose-based (nano) composites will have promising applications in the field of wastewater treatment.

Author Contributions

R-JS, TW, J-QL, NZ and M-GM: investigation. R-JS, NZ, and M-GM: supervision. R-JS, TW, J-QL, NZ and M-GM: writing-original draft. R-JS, NZ and M-GM: writing-review and editing. All authors contributed to the article and approved the submitted version.

Funding

The financial support from the National Key R & D Program of China (2019YFC1905901) and the Key Production Innovative Development Plan of the Southern Bingtuan (2019DB007) is gratefully acknowledged.

Conflict of Interest

The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest.

Publisher’s Note

All claims expressed in this article are solely those of the authors and do not necessarily represent those of their affiliated organizations, or those of the publisher, the editors and the reviewers. Any product that may be evaluated in this article, or claim that may be made by its manufacturer, is not guaranteed or endorsed by the publisher.

References

Abou-Zeid, R. E., Kamal, K. H., Abd El-Aziz, M. E., Morsi, S. M., and Kamel, S. (2021). Grafted TEMPO-Oxidized Cellulose Nanofiber Embedded with Modified Magnetite for Effective Adsorption of lead Ions. Int. J. Biol. Macromolecules 167, 1091–1101. doi:10.1016/j.ijbiomac.2020.11.063

CrossRef Full Text | Google Scholar

Ali, A. E. H. (2012). Removal of Heavy Metals from Model Wastewater by Using Carboxymehyl Cellulose/2-Acrylamido-2-Methyl Propane Sulfonic Acid Hydrogels. J. Appl. Polym. Sci. 123, 763–769. doi:10.1002/app.34470

CrossRef Full Text | Google Scholar

Ali, I., Asim, M., and Khan, T. A. (2012). Low Cost Adsorbents for the Removal of Organic Pollutants from Wastewater. J. Environ. Manage. 113, 170–183. doi:10.1016/j.jenvman.2012.08.028

PubMed Abstract | CrossRef Full Text | Google Scholar

Alila, S., and Boufi, S. (2009). Removal of Organic Pollutants from Water by Modified Cellulose Fibres. Ind. Crops Prod. 30, 93–104. doi:10.1016/j.indcrop.2009.02.005

CrossRef Full Text | Google Scholar

Anirudhan, T. S., Jalajamony, S., and Divya, L. (2009). Efficiency of Amine-Modified Poly(glycidyl Methacrylate)-Grafted Cellulose in the Removal and Recovery of Vanadium(V) from Aqueous Solutions. Ind. Eng. Chem. Res. 48, 2118–2124. doi:10.1021/ie8000869

CrossRef Full Text | Google Scholar

Anirudhan, T. S., Rauf, T. A., and Rejeena, S. R. (2012). Removal and Recovery of Phosphate Ions from Aqueous Solutions by Amine Functionalized Epichlorohydrin-Grafted Cellulose. Desalination 285, 277–284. doi:10.1016/j.desal.2011.10.014

CrossRef Full Text | Google Scholar

Anirudhan, T. S., and Rejeena, S. R. (2011). Thorium(IV) Removal and Recovery from Aqueous Solutions Using Tannin-Modified Poly(glycidylmethacrylate)-Grafted Zirconium Oxide Densified Cellulose. Ind. Eng. Chem. Res. 50, 13288–13298. doi:10.1021/ie2015679

CrossRef Full Text | Google Scholar

Arthanareeswaran, G., Thanikaivelan, P., Jaya, N., Mohan, D., and Raajenthiren, M. (2007a). Removal of Chromium from Aqueous Solution Using Cellulose Acetate and Sulfonated Poly(Ether Ether Ketone) Blend Ultrafiltration Membranes. J. Hazard. Mater. 139, 44–49. doi:10.1016/j.jhazmat.2006.06.006

CrossRef Full Text | Google Scholar

Arthanareeswaran, G., Thanikaivelan, P., Raguime, J. A., Raajenthiren, M., and Mohan, D. (2007b). Metal Ion Separation and Protein Removal from Aqueous Solutions Using Modified Cellulose Acetate Membranes: Role of Polymeric Additives. Separat. Purif. Technol. 55, 8–15. doi:10.1016/j.seppur.2006.10.014

CrossRef Full Text | Google Scholar

Asgher, M., Ahmad, Z., and Iqbal, H. M. N. (2013). Alkali and Enzymatic Delignification of Sugarcane Bagasse to Expose Cellulose Polymers for Saccharification and Bio-Ethanol Production. Ind. Crops Prod. 44, 488–495. doi:10.1016/j.indcrop.2012.10.005

CrossRef Full Text | Google Scholar

Babel, S., and Kurniawan, T. A. (2003). Low-Cost Adsorbents for Heavy Metals Uptake from Contaminated Water: A Review. J. Hazard. Mater. 97 (1-3), 219–243. doi:10.1016/s0304-3894(02)00263-7

PubMed Abstract | CrossRef Full Text | Google Scholar

Belhalfaoui, B., Aziz, A., Elandaloussi, E. H., Ouali, M. S., and De Ménorval, L. C. (2009). Succinate-Bonded Cellulose: A Regenerable and Powerful Sorbent for Cadmium-Removal from Spiked High-Hardness Groundwater. J. Hazard. Mater. 169, 831–837. doi:10.1016/j.jhazmat.2009.04.021

PubMed Abstract | CrossRef Full Text | Google Scholar

Beutler, E., and Gelbart, T. (1986). The Mechanism of Removal of Leukocytes by Cellulose Columns. Blood cells 12, 57–64.

PubMed Abstract | Google Scholar

Bisla, V., Rattan, G., Singhal, S., and Kaushik, A. (2020). Green and Novel Adsorbent from Rice Straw Extracted Cellulose for Efficient Adsorption of Hg (II) Ions in an Aqueous Medium. Int. J. Biol. Macromolecules 161, 194–203. doi:10.1016/j.ijbiomac.2020.06.035

PubMed Abstract | CrossRef Full Text | Google Scholar

Bódalo, A., Gómez, J.-L., Gómez, E., León, G., and Tejera, M. (2005). Ammonium Removal from Aqueous Solutions by Reverse Osmosis Using Cellulose Acetate Membranes. Desalination 184, 149–155. doi:10.1016/j.desal.2005.03.062

CrossRef Full Text | Google Scholar

Bontea, D., Mita, C., and Humelnicu, D. (2006). Removal of Uranyl Ions from Wastewaters Using Cellulose and Modified Cellulose Materials. J. Radioanal. Nucl. Chem. 268, 305–311. doi:10.1007/s10967-006-0167-9

CrossRef Full Text | Google Scholar

Butnaru, R., Bertea, A., and Dobrescu, L. (2003). Colour Removal of Wastewaters from Cellulose Fibers' Dyeing with Direct Dyes by Electrocoagulation. Cellul. Chem. Technol. 37, 477–486.

Google Scholar

Cao, W.-T., Chen, F.-F., Zhu, Y.-J., Zhang, Y.-G., Jiang, Y.-Y., Ma, M.-G., et al. (2018). Binary Strengthening and Toughening of MXene/Cellulose Nanofiber Composite Paper with Nacre-Inspired Structure and Superior Electromagnetic Interference Shielding Properties. ACS Nano 12, 4583–4593. doi:10.1021/acsnano.8b00997

PubMed Abstract | CrossRef Full Text | Google Scholar

Cao, W., Ma, C., Tan, S., Ma, M., Wan, P., and Chen, F. (2019). Ultrathin and Flexible CNTs/MXene/Cellulose Nanofibrils Composite Paper for Electromagnetic Interference Shielding. Nano-Micro Lett. 11, 72. doi:10.1007/s40820-019-0304-y

CrossRef Full Text | Google Scholar

Cao, W. T., Ouyang, H., Xin, W., Chao, S., Ma, C., Li, Z., et al. (2020). A Stretchable Highoutput Triboelectric Nanogenerator Improved by MXene Liquid Electrode with High Electronegativity. Adv. Funct. Mater. 30, 2004181. doi:10.1002/adfm.202004181

CrossRef Full Text | Google Scholar

Cavus, S., Gurdag, G., Yasar, M., Guclu, K., and Gurkaynak, M. A. (2006). The Competitive Heavy Metal Removal by Hydroxyethyl Cellulose-G-Poly(acrylic Acid) Copolymer and its Sodium Salt: The Effect of Copper Content on the Adsorption Capacity. Polym. Bull. 57, 445–456. doi:10.1007/s00289-006-0583-6

CrossRef Full Text | Google Scholar

Chen, H., Wang, X., Li, J., and Wang, X. (2015). Cotton Derived Carbonaceous Aerogels for the Efficient Removal of Organic Pollutants and Heavy Metal Ions. J. Mater. Chem. A. 3, 6073–6081. doi:10.1039/c5ta00299k

CrossRef Full Text | Google Scholar

Chen, S., Zou, Y., Yan, Z., Shen, W., Shi, S., Zhang, X., et al. (2009). Carboxymethylated-Bacterial Cellulose for Copper and lead Ion Removal. J. Hazard. Mater. 161, 1355–1359. doi:10.1016/j.jhazmat.2008.04.098

PubMed Abstract | CrossRef Full Text | Google Scholar

Chen, W., Ma, H., and Xing, B. (2020). Electrospinning of Multifunctional Cellulose Acetate Membrane and its Adsorption Properties for Ionic Dyes. Int. J. Biol. Macromolecules 158, 1342–1351. doi:10.1016/j.ijbiomac.2020.04.249

PubMed Abstract | CrossRef Full Text | Google Scholar

Choi, H. Y., Bae, J. H., Hasegawa, Y., An, S., Kim, I. S., Lee, H., et al. (2020). Thiol-Functionalized Cellulose Nanofiber Membranes for the Effective Adsorption of Heavy Metal Ions in Water. Carbohydr. Polym. 234, 115881. doi:10.1016/j.carbpol.2020.115881

PubMed Abstract | CrossRef Full Text | Google Scholar

Choi, S., and Jeong, Y. (2008). The Removal of Heavy Metals in Aqueous Solution by Hydroxyapatite/Cellulose Composite. Fibers Polym. 9, 267–270. doi:10.1007/s12221-008-0042-0

CrossRef Full Text | Google Scholar

Çifci, C., and Kaya, A. (2010). Preparation of Poly(Vinyl Alcohol)/Cellulose Composite Membranes for Metal Removal from Aqueous Solutions. Desalination 253, 175–179. doi:10.1016/j.desal.2009.11.010

CrossRef Full Text | Google Scholar

Crini, G. (2006). Non-Conventional Low-Cost Adsorbents for Dye Removal: A Review. Bioresour. Technol. 97 (9), 1061–1085. doi:10.1016/j.biortech.2005.05.001

PubMed Abstract | CrossRef Full Text | Google Scholar

Dai, H., Chen, Y., Ma, L., Zhang, Y., and Cui, B. (2021). Direct Regeneration of Hydrogels Based on Lemon Peel and its Isolated Microcrystalline Cellulose: Characterization and Application for Methylene Blue Adsorption. Int. J. Biol. Macromolecules 191, 129–138. doi:10.1016/j.ijbiomac.2021.09.063

CrossRef Full Text | Google Scholar

De Smet, R., Dhondt, A., Eloot, S., Galli, F., Waterloos, M. A., and Vanholder, R. (2007). Effect of the Super-Flux Cellulose Triacetate Dialyser Membrane on the Removal of Non-Protein-Bound and Protein-Bound Uraemic Solutes. Nephrol. Dial. Transplant. 22, 2006–2012. doi:10.1093/ndt/gfm065

PubMed Abstract | CrossRef Full Text | Google Scholar

Dewangan, T., Tiwari, A., and Bajpai, A. K. (2011). Removal of Chromium(VI) Ions by Adsorption onto Binary Biopolymeric Beads of Sodium Alginate and Carboxymethyl Cellulose. J. Dispersion Sci. Technol. 32, 1075–1082. doi:10.1080/01932691003659403

CrossRef Full Text | Google Scholar

Dilamian, M., and Noroozi, B. (2021). Rice Straw Agri-Waste for Water Pollutant Adsorption: Relevant Mesoporous Super Hydrophobic Cellulose Aerogel. Carbohydr. Polym. 251, 117016. doi:10.1016/j.carbpol.2020.117016

PubMed Abstract | CrossRef Full Text | Google Scholar

Ding, F., Ren, P., Wang, G., Wu, S., Du, Y., and Zou, X. (2021). Hollow Cellulose-Carbon Nanotubes Composite Beads with Aligned Porous Structure for Fast Methylene Blue Adsorption. Int. J. Biol. Macromolecules 182, 750–759. doi:10.1016/j.ijbiomac.2021.03.194

CrossRef Full Text | Google Scholar

Dong, F., Xu, X., Shaghaleh, H., Guo, J., Guo, L., Qian, Y., et al. (2020a). Factors Influencing the Morphology and Adsorption Performance of Cellulose Nanocrystal/iron Oxide Nanorod Composites for the Removal of Arsenic during Water Treatment. Int. J. Biolog. Macromol. 156, 1418–1424. doi:10.1016/j.ijbiomac.2019.11.182

CrossRef Full Text | Google Scholar

Dong, H., Zheng, L., Yu, P., Jiang, Q., Wu, Y., Huang, C., et al. (2020b). Characterization and Application of Lignin-Carbohydrate Complexes from Lignocellulosic Materials as Antioxidants for Scavenging In Vitro and In Vivo Reactive Oxygen Species. ACS Sustain. Chem. Eng. 8 (1), 256–266. doi:10.1021/acssuschemeng.9b05290

CrossRef Full Text | Google Scholar

Dridi-Dhaouadi, S., Ben Douissa-Lazreg, N., and M'Henni, M. F. (2011). Removal of lead and Yellow 44 Acid Dye in Single and Binary Component Systems by Raw Posidonia Oceanica and the Cellulose Extracted from the Raw Biomass. Environ. Technol. 32 (3), 325–340. doi:10.1080/09593330.2010.499545

PubMed Abstract | CrossRef Full Text | Google Scholar

Eberhardt, T. L., Min, S.-H., and Han, J. S. (2006). Phosphate Removal by Refined aspen Wood Fiber Treated with Carboxymethyl Cellulose and Ferrous Chloride. Bioresour. Technol. 97, 2371–2376. doi:10.1016/j.biortech.2005.10.040

PubMed Abstract | CrossRef Full Text | Google Scholar

Eltaweil, A. S., Elgarhy, G. S., El-Subruiti, G. M., and Omer, A. M. (2020). Carboxymethyl Cellulose/Carboxylated Graphene Oxide Composite Microbeads for Efficient Adsorption of Cationic Methylene Blue Dye. Int. J. Biol. Macromolecules 154, 307–318. doi:10.1016/j.ijbiomac.2020.03.122

CrossRef Full Text | Google Scholar

Fang, H., Wei, J., and Yu, Y. (2004). In Vivo Studies of Endotoxin Removal by Lysine-Cellulose Adsorbents. Biomaterials 25, 5433–5440. doi:10.1016/j.biomaterials.2003.12.035

PubMed Abstract | CrossRef Full Text | Google Scholar

Feng, C., Ren, P., Huo, M., Dai, Z., Liang, D., Jin, Y., et al. (2020). Facile Synthesis of Trimethylammonium Grafted Cellulose Foams with High Capacity for Selective Adsorption of Anionic Dyes from Water. Carbohydr. Polym. 241, 116369. doi:10.1016/j.carbpol.2020.116369

PubMed Abstract | CrossRef Full Text | Google Scholar

Franceschini, G., Busnach, G., Vaccarino, V., Calabresi, L., Gianfranceschi, G., and Sirtori, C. R. (1988). Apheretic Treatment of Severe Familial Hypercholesterolemia: Comparison of Dextran Sulfate Cellulose and Double Membrane Filtration Methods for Low Density Lipoprotein Removal. Atherosclerosis 73, 197–202. doi:10.1016/0021-9150(88)90042-1

PubMed Abstract | CrossRef Full Text | Google Scholar

Garcia-Reyes, R. B., and Rangel-Mendez, J. R. (2009). Contribution of Agro-Waste Material Main Components (Hemicelluloses, Cellulose, and Lignin) to the Removal of Chromium (III) from Aqueous Solution. J. Chem. Technol. Biotechnol. 84, 1533–1538. doi:10.1002/jctb.2215

CrossRef Full Text | Google Scholar

Ghanta, K. C., Ghosh, A. K., and Ramachandhran, V. (2005). Separation Characteristics of Cellulose Acetate Blend (CAB) and Aromatic Polyamide Hydrazide (PAH) Reverse Osmosis (RO) Membranes for Removal of Phenol from Phenol Water-Mixtures. J. Polym. Mater. 22, 313–319.

Google Scholar

Greben, H. A., Baloyi, L. J., and Venter, S. N. (2007). Grass Cellulose as Cost-Effective Energy Source for Biological Sulphate Removal. Water SA 33, 729–733. doi:10.4314/wsa.v33i5.184095

CrossRef Full Text | Google Scholar

Guo, W.-Y., Yuan, Q., Huang, L.-Z., Zhang, W., Li, D.-D., Yao, C., et al. (2022). Multifunctional Bacterial Cellulose-Based Organohydrogels with Long-Term Environmental Stability. J. Colloid Interf. Sci. 608, 820–829. doi:10.1016/j.jcis.2021.10.057

CrossRef Full Text | Google Scholar

Guo, X., and Chen, F. (2005). Removal of Arsenic by Bead Cellulose Loaded with Iron Oxyhydroxide from Groundwater. Environ. Sci. Technol. 39, 6808–6818. doi:10.1021/es048080k

PubMed Abstract | CrossRef Full Text | Google Scholar

Guo, X., Du, Y., Chen, F., Park, H.-S., and Xie, Y. (2007). Mechanism of Removal of Arsenic by Bead Cellulose Loaded with Iron Oxyhydroxide (β-FeOOH): EXAFS Study. J. Coll. Interf. Sci. 314, 427–433. doi:10.1016/j.jcis.2007.05.071

CrossRef Full Text | Google Scholar

Güçlü, G., Gürdağ, G., and Özgümüş, S. (2003). Competitive Removal of Heavy Metal Ions by Cellulose Graft Copolymers. J. Appl. Polym. Sci. 90, 2034–2039. doi:10.1002/app.12728

CrossRef Full Text | Google Scholar

Hashem, A., Abou-Okeil, A., El-Shafie, A., and El-Sakhawy, M. (2006). Grafting of High α-Cellulose Pulp Extracted from Sunflower Stalks for Removal of Hg (II) from Aqueous Solution. Polymer-Plastics Technol. Eng. 45, 135–141. doi:10.1080/03602550500373790

CrossRef Full Text | Google Scholar

Hashem, A., Fletcher, A. J., Younis, H., Mauof, H., and Abou-Okeil, A. (2020). Adsorption of Pb(II) Ions from Contaminated Water by 1,2,3,4-butanetetracarboxylic Acid-Modified Microcrystalline Cellulose: Isotherms, Kinetics, and Thermodynamic Studies. Int. J. Biol. Macromolecules 164, 3193–3203. doi:10.1016/j.ijbiomac.2020.08.159

PubMed Abstract | CrossRef Full Text | Google Scholar

Heppner, C., Åkesson, A., Amzal, B., Di Domenico, A., Dorne, J. L. C. M., Cristoph, E. H., et al. (2009). Risk Assessment of Cadmium in Food: Implications for Human Health. Toxicol. Lett. 189, S233. doi:10.1016/j.toxlet.2009.06.500

CrossRef Full Text | Google Scholar

Huang, C., Cai, B., Zhang, L., Zhang, C., and Pan, H. (2021a). Preparation of Iron-Based Metal-Organic Framework @cellulose Aerogel by In Situ Growth Method and its Application to Dye Adsorption. J. Solid State. Chem. 297, 122030. doi:10.1016/j.jssc.2021.122030

CrossRef Full Text | Google Scholar

Huang, C., Dong, H., Zhang, Z., Bian, H., and Yong, Q. (2020). Procuring the Nano-Scale Lignin in Prehydrolyzate as Ingredient to Prepare Cellulose Nanofibril Composite Film with Multiple Functions. Cellulose 27 (16), 9355–9370. doi:10.1007/s10570-020-03427-9

CrossRef Full Text | Google Scholar

Huang, C., Dong, J., Zhang, Y., Chai, S., Wang, X., Kang, S., et al. (2021b). Gold Nanoparticles-Loaded Polyvinylpyrrolidone/Ethylcellulose Coaxial Electrospun Nanofibers with Enhanced Osteogenic Capability for Bone Tissue Regeneration. Mater. Des. 212, 110240. doi:10.1016/j.matdes.2021.110240

CrossRef Full Text | Google Scholar

Huang, C., Tang, S., Zhang, W., Tao, Y., Lai, C., Li, X., et al. (2018). Unveiling the Structural Properties of Lignin-Carbohydrate Complexes in Bamboo Residues and its Functionality as Antioxidants and Immunostimulants. ACS Sustain. Chem. Eng. 6 (9), 12522–12531. doi:10.1021/acssuschemeng.8b03262

CrossRef Full Text | Google Scholar

Inukai, Y., Tanaka, Y., Matsuda, T., Mihara, N., Yamada, K., Nambu, N., et al. (2004). Removal of Boron(III) by N-Methylglucamine-Type Cellulose Derivatives with Higher Adsorption Rate. Analytica Chim. Acta 511, 261–265. doi:10.1016/j.aca.2004.01.054

CrossRef Full Text | Google Scholar

Islam, M., Mishra, P. C., and Patel, R. (2011). Arsenate Removal from Aqueous Solution by Cellulose-Carbonated Hydroxyapatite Nanocomposites. J. Hazard. Mater. 189, 755–763. doi:10.1016/j.jhazmat.2011.03.051

PubMed Abstract | CrossRef Full Text | Google Scholar

Jarup, L., and Akesson, A. (2009). Current Status of Cadmium as an Environmental Health Problem. Toxicol. Appl. Pharmacol. 238 (3), 201–208. doi:10.1016/j.taap.2009.04.020

PubMed Abstract | CrossRef Full Text | Google Scholar

Kamel, S., Hassan, E. M., and El-Sakhawy, M. (2006). Preparation and Application of Acrylonitrile-Grafted Cyanoethyl Cellulose for the Removal of Copper (II) Ions. J. Appl. Polym. Sci. 100, 329–334. doi:10.1002/app.23317

CrossRef Full Text | Google Scholar

Karnitz, O., Gurgel, L. V. A., and Gil, L. F. (2010). Removal of Ca(II) and Mg(II) from Aqueous Single Metal Solutions by Mercerized Cellulose and Mercerized Sugarcane Bagasse Grafted with EDTA Dianhydride (EDTAD). Carbohydr. Polym. 79, 184–191. doi:10.1016/j.carbpol.2009.07.048

CrossRef Full Text | Google Scholar

Klemm, D., Heublein, B., Fink, H.-P., and Bohn, A. (2005). Cellulose: Fascinating Biopolymer and Sustainable Raw Material. Angew. Chem. Int. Ed. 44, 3358–3393. doi:10.1002/anie.200460587

CrossRef Full Text | Google Scholar

Kong, Q., Wang, X., and Lou, T. (2020). Preparation of Millimeter-Sized Chitosan/Carboxymethyl Cellulose Hollow Capsule and its Dye Adsorption Properties. Carbohydr. Polym. 244, 116481. doi:10.1016/j.carbpol.2020.116481

PubMed Abstract | CrossRef Full Text | Google Scholar

Kumar, A. S. K., Kalidhasan, S., Rajesh, V., and Rajesh, N. (2012). Application of Cellulose-Clay Composite Biosorbent toward the Effective Adsorption and Removal of Chromium from Industrial Wastewater. Ind. Eng. Chem. Res. 51, 58–69. doi:10.1021/ie201349h

CrossRef Full Text | Google Scholar

Li, M., Zhang, S., Cui, S., Qin, K., Zhang, Y., Li, P., et al. (2021). Pre-Grafting Effect on Improving Adsorption Efficiency of Cellulose Based Biosorbent for Hg (II) Removal from Aqueous Solution. Separat. Purif. Technol. 277, 119493. doi:10.1016/j.seppur.2021.119493

CrossRef Full Text | Google Scholar

Li, S.-M., Jia, N., Ma, M.-G., Zhang, Z., Liu, Q.-H., and Sun, R.-C. (2011). Cellulose-Silver Nanocomposites: Microwave-Assisted Synthesis, Characterization, Their Thermal Stability, and Antimicrobial Property. Carbohydr. Polym. 86, 441–447. doi:10.1016/j.carbpol.2011.04.060

CrossRef Full Text | Google Scholar

Li, X., Tang, Y., Cao, X., Lu, D., Luo, F., and Shao, W. (2008). Preparation and Evaluation of Orange Peel Cellulose Adsorbents for Effective Removal of Cadmium, Zinc, Cobalt and Nickel. Colloids Surf. A: Physicochemical Eng. Aspects 317, 512–521. doi:10.1016/j.colsurfa.2007.11.031

CrossRef Full Text | Google Scholar

Lian, Z., Li, Y., Xian, H., Ouyang, X.-k., Lu, Y., Peng, X., et al. (2020). EDTA-Functionalized Magnetic Chitosan Oligosaccharide and Carboxymethyl Cellulose Nanocomposite: Synthesis, Characterization, and Pb(II) Adsorption Performance. Int. J. Biol. Macromolecules 165, 591–600. doi:10.1016/j.ijbiomac.2020.09.156

PubMed Abstract | CrossRef Full Text | Google Scholar

Lima, I. S., Lazarin, A. M., and Airoldi, C. (2005). Favorable Chitosan/Cellulose Film Combinations for Copper Removal from Aqueous Solutions. Int. J. Biol. Macromolecules 36, 79–83. doi:10.1016/j.ijbiomac.2005.04.001

CrossRef Full Text | Google Scholar

Liu, C., and Bai, R. (2006). Adsorptive Removal of Copper Ions with Highly Porous Chitosan/Cellulose Acetate Blend Hollow Fiber Membranes. J. Membr. Sci. 284, 313–322. doi:10.1016/j.memsci.2006.07.045

CrossRef Full Text | Google Scholar

Liu, M., Zhang, H., Zhang, X., Deng, Y., Liu, W., and Zhan, H. (2001). Removal and Recovery of Chromium (III) from Aqueous Solutions by a Spheroidal Cellulose Adsorbent. Water Environm. Res. 73, 322–328. doi:10.2175/106143001x139344

PubMed Abstract | CrossRef Full Text | Google Scholar

Liu, S., Du, X.-L., Ma, C., Ji, X.-X., Ma, M.-G., and Li, J.-F. (2019). Synthesis of Magnetic Carbon/Iron Oxide Nanocomposites in Ethylene Glycol/water Mixed Solvents and Their Highly Adsorption Performance. Sci. Adv. Mater. 11, 33–40. doi:10.1166/sam.2019.3349

CrossRef Full Text | Google Scholar

Liu, T., Wang, Z., Wang, X., Yang, G., and Liu, Y. (2021a). Adsorption-Photocatalysis Performance of Polyaniline/Dicarboxyl Acid Cellulose@graphene Oxide for Dye Removal. Int. J. Biolog. Macromol. 182, 492–501. doi:10.1016/j.ijbiomac.2021.04.038

CrossRef Full Text | Google Scholar

Liu, Y.-J., Cao, W.-T., Ma, M.-G., and Wan, P. (2017). Ultrasensitive Wearable Soft Strain Sensors of Conductive, Self-Healing, and Elastic Hydrogels with Synergistic "Soft and Hard" Hybrid Networks. ACS Appl. Mater. Inter. 9, 25559–25570. doi:10.1021/acsami.7b07639

PubMed Abstract | CrossRef Full Text | Google Scholar

Liu, Y.-J., Liu, S., Li, Z.-W., Ma, M.-G., and Wang, B. (2018). Microwave Synthetic Mesoporous Carbon Sponge as an Efficient Adsorbent for Cr(VI) Removal. RSC Adv. 8, 7892–7898. doi:10.1039/c8ra00012c

CrossRef Full Text | Google Scholar

Liu, Y., Nie, P., and Yu, F. (2021b). Enhanced Adsorption of Sulfonamides by a Novel Carboxymethyl Cellulose and Chitosan-Based Composite with Sulfonated Graphene Oxide. Bioresour. Technol. 320, 124373. doi:10.1016/j.biortech.2020.124373

PubMed Abstract | CrossRef Full Text | Google Scholar

Lü, L., Lu, D., Chen, L., and Luo, F. (2010). Removal of Cd (II) by Modified Lawny Grass Cellulose Adsorbent. Desalination 259, 120–130. doi:10.1016/j.desal.2010.04.022

CrossRef Full Text | Google Scholar

Ma, C., Cao, W. T., Zhang, W., Ma, M. G., Sun, W. M., Zhang, J., et al. (2021). Wearable, Ultrathin and Transparent Bacterial Celluloses/MXene Film with Janus Structure and Excellent Mechanical Property for Electromagnetic Interference Shielding. Chem. Eng. J. 403, 126438. doi:10.1016/j.cej.2020.126438

CrossRef Full Text | Google Scholar

Mai, T., Wang, P.-L., Yuan, Q., Ma, C., and Ma, M.-G. (2021). In Situ Anchoring Zn-Doped ZIF-67 on Carboxymethylated Bacterial Cellulose for Effective Indigo Carmine Capture. Nanoscale 13, 18210–18217. doi:10.1039/d1nr05388d

PubMed Abstract | CrossRef Full Text | Google Scholar

Maliyekkal, S. M., Lisha, K. P., and Pradeep, T. (2010). A Novel Cellulose-Manganese Oxide Hybrid Material by In Situ Soft Chemical Synthesis and its Application for the Removal of Pb(II) from Water. J. Hazard. Mater. 181, 986–995. doi:10.1016/j.jhazmat.2010.05.112

PubMed Abstract | CrossRef Full Text | Google Scholar

Mansfield, S. D., Mooney, C., and Saddler, J. N. (1999). Substrate and Enzyme Characteristics that Limit Cellulose Hydrolysis. Biotechnol. Prog. 15, 804–816. doi:10.1021/bp9900864

PubMed Abstract | CrossRef Full Text | Google Scholar

Meneses, I. P., Novaes, S. D., Dezotti, R. S., Oliveira, P. V., and Petri, D. F. S. (2022). CTAB-Modified Carboxymethyl Cellulose/Bagasse Cryogels for the Efficient Removal of Bisphenol A, Methylene Blue and Cr(VI) Ions: Batch and Column Adsorption Studies. J. Hazard. Mater. 421, 126804. doi:10.1016/j.jhazmat.2021.126804

PubMed Abstract | CrossRef Full Text | Google Scholar

Menon, V., and Rao, M. (2012). Trends in Bioconversion of Lignocellulose: Biofuels, Platform Chemicals & Biorefinery Concept. Prog. Energ. Combustion Sci. 38 (4), 522–550. doi:10.1016/j.pecs.2012.02.002

CrossRef Full Text | Google Scholar

Mohan, D., and Pittman, C. U. (2006). Activated Carbons and Low Cost Adsorbents for Remediation of Tri- and Hexavalent Chromium from Water. J. Hazard. Mater. 137 (2), 762–811. doi:10.1016/j.jhazmat.2006.06.060

PubMed Abstract | CrossRef Full Text | Google Scholar

Musyoka, S. M., Ngila, J. C., Moodley, B., Petrik, L., and Kindness, A. (2011). Synthesis, Characterization, and Adsorption Kinetic Studies of Ethylenediamine Modified Cellulose for Removal of Cd and Pb. Anal. Lett. 44, 1925–1936. doi:10.1080/00032719.2010.539736

CrossRef Full Text | Google Scholar

Nata, I. F., Sureshkumar, M., and Lee, C.-K. (2011). One-pot Preparation of Amine-Rich Magnetite/Bacterial Cellulose Nanocomposite and its Application for Arsenate Removal. RSC Adv. 1, 625–631. doi:10.1039/c1ra00153a

CrossRef Full Text | Google Scholar

Norkus, E., Vaičiūnienė, J., and Vuorinen, T. (2006). Removal of Transition Metals from Alkaline Suspensions of Cellulose Pulp Using CDTA as Chelating Agent. Carbohydr. Polym. 66, 316–320. doi:10.1016/j.carbpol.2006.03.018

CrossRef Full Text | Google Scholar

Nzediegwu, E., and Dumont, M.-J. (2021). Chemo-Catalytic Transformation of Cellulose and Cellulosic-Derived Waste Materials into Platform Chemicals. Waste Biomass Valor. 12 (6), 2825–2851. doi:10.1007/s12649-020-01179-y

CrossRef Full Text | Google Scholar

O'Connell, D. W., Birkinshaw, C., and O'Dwyer, T. F. (2008). Heavy Metal Adsorbents Prepared from the Modification of Cellulose: A Review. Bioresour. Technol. 99, 6709–6724. doi:10.1016/j.biortech.2008.01.036

PubMed Abstract | CrossRef Full Text | Google Scholar

O'Connell, D. W., Birkinshaw, C., and O'Dwyer, T. F. (2006a). A Modified Cellulose Adsorbent for the Removal of Nickel (II) from Aqueous Solutions. J. Chem. Technol. Biotechnol. 81, 1820–1828. doi:10.1002/jctb.1609

CrossRef Full Text | Google Scholar

O'Connell, D. W., Birkinshaw, C., and O'Dwyer, T. F. (2006b). Removal of Lead (II) Ions from Aqueous Solutions Using a Modified Cellulose Adsorbent. Adsorpt. Sci. Technol. 24, 337–348. doi:10.1260/026361706779319670

CrossRef Full Text | Google Scholar

Okieimen, F. E., Sogbaike, C. E., and Ebhoaye, J. E. (2005). Removal of Cadmium and Copper Ions from Aqueous Solution with Cellulose Graft Copolymers. Separat. Purif. Technol. 44, 85–89. doi:10.1016/j.seppur.2004.11.003

CrossRef Full Text | Google Scholar

Olbricht, C. J. (1996). Extracorporeal Removal of Lipids by Dextran Sulfate Cellulose Adsorption. Artif. Organs 20 (4), 332–335. doi:10.1111/j.1525-1594.1996.tb04454.x

PubMed Abstract | CrossRef Full Text | Google Scholar

Park, S.-H., Shin, S. S., Park, C. H., Jeon, S., Gwon, J., Lee, S.-Y., et al. (2020). Poly(acryloyl Hydrazide)-Grafted Cellulose Nanocrystal Adsorbents with an Excellent Cr(VI) Adsorption Capacity. J. Hazard. Mater. 394, 122512. doi:10.1016/j.jhazmat.2020.122512

PubMed Abstract | CrossRef Full Text | Google Scholar

Qu, J., Tian, X., Jiang, Z., Cao, B., Akindolie, M. S., Hu, Q., et al. (2020). Multi-Component Adsorption of Pb(II), Cd(II) and Ni(II) onto Microwavefunctionalized Cellulose: Kinetics, Isotherms, Thermodynamics, Mechanisms and Application for Electroplating Wastewater Purification. J. Hazard. Mater. 387, 121718. doi:10.1016/j.jhazmat.2019.121718

PubMed Abstract | CrossRef Full Text | Google Scholar

Rahmatika, A. M., Goi, Y., Kitamura, T., Morita, Y., Iskandar, F., and Ogi, T. (2020). Silica-Supported Carboxylated Cellulose Nanofibers for Effective Lysozyme Adsorption: Effect of Macropore Size. Adv. Powder Technol. 31, 2932–2941. doi:10.1016/j.apt.2020.05.021

CrossRef Full Text | Google Scholar

Rong, N., Chen, C., Ouyang, K., Zhang, K., Wang, X., and Xu, Z. (2021). Adsorption Characteristics of Directional Cellulose Nanofiber/Chitosan/Montmorillonite Aerogel as Adsorbent for Wastewater Treatment. Separat. Purif. Technol. 274, 119120. doi:10.1016/j.seppur.2021.119120

CrossRef Full Text | Google Scholar

Sakata, M., Todokoro, M., and Kunitake, M. (2007). Pore-Size Controlled and Polycation-Immobilized Cellulose Spherical Particles for Removal of Endotoxin. Kobunshi Ronbunshu 64, 821–829. doi:10.1295/koron.64.821

CrossRef Full Text | Google Scholar

Schulzeck, P., Olbricht, C. J., and Koch, K. M. (1992). Long-Term Experience with Extracorporeal Low-Density Lipoprotein Cholesterol Removal by Dextran Sulfate Cellulose Adsorption. Clin. Investig. 70, 99–104. doi:10.1007/BF00227348

PubMed Abstract | CrossRef Full Text | Google Scholar

Sepahvand, S., Jonoobi, M., Ashori, A., Gauvin, F., Brouwers, H. J. H., Oksman, K., et al. (2020). A Promising Process to Modify Cellulose Nanofibers for Carbon Dioxide (CO2) Adsorption. Carbohydr. Polym. 230, 115571. doi:10.1016/j.carbpol.2019.115571

PubMed Abstract | CrossRef Full Text | Google Scholar

Shao, D., Jiang, Z., Wang, X., Li, J., and Meng, Y. (2009). Plasma Induced Grafting Carboxymethyl Cellulose on Multiwalled Carbon Nanotubes for the Removal of UO₂²⁺ from Aqueous Solution. J. Phys. Chem. B 113, 860–864. doi:10.1021/jp8091094

PubMed Abstract | CrossRef Full Text | Google Scholar

Shukla, S., and Pai, R. S. (2005). Removal of Pb(II) from Solution Using Cellulose-Containing Materials. J. Chem. Technol. Biotechnol. 80, 176–183. doi:10.1002/jctb.1176

CrossRef Full Text | Google Scholar

Takagai, Y., Shibata, A., Kiyokawa, S., and Takase, T. (2011). Synthesis and Evaluation of Different Thio-Modified Cellulose Resins for the Removal of Mercury (II) Ion from Highly Acidic Aqueous Solutions. J. Colloid Interf. Sci. 353, 593–597. doi:10.1016/j.jcis.2010.09.070

CrossRef Full Text | Google Scholar

Tiwari, A., Dewangan, T., and Bajpai, A. K. (2008). Removal of Toxic as (V) Ions by Adsorption onto Alginate and Carboxymethyl Cellulose Beads. Jnl Chin. Chem. Soc 55, 952–961. doi:10.1002/jccs.200800142

CrossRef Full Text | Google Scholar

Volesky, B., and Holan, Z. R. (1995). Biosorption of Heavy Metals. Biotechnol. Prog. 11 (3), 235–250. doi:10.1021/bp00033a001

PubMed Abstract | CrossRef Full Text | Google Scholar

Wang, P.-L., Ma, C., Yuan, Q., Mai, T., and Ma, M.-G. (2022). Novel Ti₃C₂T_x MXene Wrapped Wood Sponges for Fast Cleanup of Crude Oil Spills by Outstanding Joule Heating and Photothermal Effect. J. Coll. Interf. Sci. 606, 971–982. doi:10.1016/j.jcis.2021.08.092

CrossRef Full Text | Google Scholar

Wang, P., Yin, B., Dong, H., Zhang, Y., Zhang, Y., Chen, R., et al. (2020a). Coupling Biocompatible Au Nanoclusters and Cellulose Nanofibrils to Prepare the Antibacterial Nanocomposite Films. Front. Bioeng. Biotechnol. 8, 986. doi:10.3389/fbioe.2020.00986

PubMed Abstract | CrossRef Full Text | Google Scholar

Wang, R., Deng, L., Fan, X., Li, K., Lu, H., and Li, W. (2021a). Removal of Heavy Metal Ion Co²⁺ from Wastewater via Adsorption Method Using Microcrystalline Cellulose-Magnesium Hydroxide. Int. J. Biolog. Macromol. 189, 607–617. doi:10.1016/j.ijbiomac.2021.08.156

CrossRef Full Text | Google Scholar

Wang, S., Guo, X., Wang, L., Wang, W., and Yu, Y. (2006). Effect of PEG Spacer on Cellulose Adsorbent for the Removal of Low Density Lipoprotein-Cholesterol. Artif. Cell Blood Substitutes, Biotechnol. 34, 101–112. doi:10.1080/10731190500430222

CrossRef Full Text | Google Scholar

Wang, S. Q., Yu, Y. T., Cui, T., and Cheng, Y. (2002). Cellulose Amphiphilic Adsorbent for the Removal of Low Density Lipoprotein. Artificial Cells, Blood Substitutes. Immobilization Biotechnol. 30, 285–292. doi:10.1081/BIO-120006119

CrossRef Full Text | Google Scholar

Wang, X., Tang, S., Chai, S., Wang, P., Qin, J., Pei, W., et al. (2021b). Preparing Printable Bacterial Cellulose Based Gelatin Gel to Promote In Vivo Bone Regeneration. Carbohydr. Polym. 270, 118342. doi:10.1016/j.carbpol.2021.118342

PubMed Abstract | CrossRef Full Text | Google Scholar

Wang, Y., Li, C., Zheng, Y., Xie, Y., Qiao, K., He, W., et al. (2021c). Plant Protein Modified Natural Cellulose with Multiple Adsorption Effects Used for Bilirubin Removal. Int. J. Biol. Macromolecules 166, 179–189. doi:10.1016/j.ijbiomac.2020.10.131

CrossRef Full Text | Google Scholar

Wang, Z., Song, L., Wang, Y., Zhang, X.-F., Hao, D., Feng, Y., et al. (2019). Lightweight UiO-66/Cellulose Aerogels Constructed through Self-Crosslinking Strategy for Adsorption Applications. Chem. Eng. J. 371, 138–144. doi:10.1016/j.cej.2019.04.022

CrossRef Full Text | Google Scholar

Wang, Z., Yao, M., Wang, X., Li, S., Liu, Y., and Yang, G. (2020b). Influence of Reaction media on Synthesis of Dialdehyde Cellulose/GO Composites and Their Adsorption Performances on Heavy Metals. Carbohydr. Polym. 232, 115781. doi:10.1016/j.carbpol.2019.115781

PubMed Abstract | CrossRef Full Text | Google Scholar

Weber, C., Henne, B., Loth, F., Schoenhofen, M., and Falkenhagen, D. (1995). Development of Cationically Modified Cellulose Adsorbents for the Removal of Endotoxins. ASAIO J. 41, M430–M434. doi:10.1097/00002480-199507000-00046

PubMed Abstract | CrossRef Full Text | Google Scholar

Wen, D., Dong, Z., Ao, Y., Xie, K., Zhai, M., and Zhao, L. (2021). Aminotriazole Isomers Modified Cellulose Microspheres for Selective Adsorption of U(VI): Performance and Mechanism Investigation. Carbohydr. Polym. 257, 117666. doi:10.1016/j.carbpol.2021.117666

PubMed Abstract | CrossRef Full Text | Google Scholar

Wittmar, A. S. M., Klug, J., and Ulbricht, M. (2020). Cellulose/Chitosan Porous Spheres Prepared from 1-Butyl-3-Methylimidazolium Acetate/Dimethylformamide Solutions for Cu²⁺ Adsorption. Carbohydr. Polym. 237, 116135. doi:10.1016/j.carbpol.2020.116135

PubMed Abstract | CrossRef Full Text | Google Scholar

Wu, L., and Ritchie, S. M. C. (2006). Removal of Trichloroethylene from Water by Cellulose Acetate Supported Bimetallic Ni/Fe Nanoparticles. Chemosphere 63, 285–292. doi:10.1016/j.chemosphere.2005.07.021

PubMed Abstract | CrossRef Full Text | Google Scholar

Xie, K., Jing, L., Zhao, W., and Zhang, Y. (2011a). Adsorption Removal of Cu²⁺ and Ni²⁺ from Waste Water Using Nano-Cellulose Hybrids Containing Reactive Polyhedral Oligomeric Silsesquioxanes. J. Appl. Polym. Sci. 122, 2864–2868. doi:10.1002/app.34411

CrossRef Full Text | Google Scholar

Xie, K., Zhao, W., and He, X. (2011b). Adsorption Properties of Nano-Cellulose Hybrid Containing Polyhedral Oligomeric Silsesquioxane and Removal of Reactive Dyes from Aqueous Solution. Carbohydr. Polym. 83, 1516–1520. doi:10.1016/j.carbpol.2010.09.064

CrossRef Full Text | Google Scholar

Xu, Z., Bae, W., Mulchandani, A., Mehra, R. K., and Chen, W. (2002). Heavy Metal Removal by Novel CBD-EC20 Sorbents Immobilized on Cellulose. Biomacromolecules 3, 462–465. doi:10.1021/bm015631f

PubMed Abstract | CrossRef Full Text | Google Scholar

Yagub, M. T., Sen, T. K., Afroze, S., and Ang, H. M. (2014). Dye and its Removal from Aqueous Solution by Adsorption: A Review. Adv. Colloid Interf. Sci. 209, 172–184. doi:10.1016/j.cis.2014.04.002

CrossRef Full Text | Google Scholar

Yan, L., Shuai, Q., Gong, X., Gu, Q., and Yu, H. (2009). Synthesis of Microporous Cationic Hydrogel of Hydroxypropyl Cellulose (HPC) and its Application on Anionic Dye Removal. Clean. Soil Air Water 37, 392–398. doi:10.1002/clen.200900006

CrossRef Full Text | Google Scholar

Yang, H.-R., Li, S.-S., An, Q.-D., Zhai, S.-R., Xiao, Z.-Y., and Zhang, L.-P. (2021). Facile Transformation of Carboxymethyl Cellulose Beads into Hollow Composites for Dye Adsorption. Int. J. Biol. Macromolecules 190, 919–926. doi:10.1016/j.ijbiomac.2021.08.229

CrossRef Full Text | Google Scholar

Yang, S., Fu, S., Liu, H., Zhou, Y., and Li, X. (2011). Hydrogel Beads Based on Carboxymethyl Cellulose for Removal Heavy Metal Ions. J. Appl. Polym. Sci. 119, 1204–1210. doi:10.1002/app.32822

CrossRef Full Text | Google Scholar

Yang, X., Cao, Y.-M., Wang, R., and Yuan, Q. (2007). Study on Highly Hydrophilic Cellulose Hollow Fiber Membrane Contactors for Thiol Sulfur Removal. J. Membr. Sci. 305, 247–256. doi:10.1016/j.memsci.2007.08.020

CrossRef Full Text | Google Scholar

Yi, Q., Lu, S., Fan, Y., Cheng, D., Wang, X., Cheng, S., et al. (2022). Preparation and Adsorption Performance of Cellulose Nanofibrils/polyvinyl Alcohol Composite Gel Spheres with Millimeter Size. Carbohydr. Polym. 277, 118850. doi:10.1016/j.carbpol.2021.118850

PubMed Abstract | CrossRef Full Text | Google Scholar

You, X., Wang, R., Zhu, Y., Sui, W., and Cheng, D. (2021). Comparison of Adsorption Properties of a Cellulose-Rich Modified rice Husk for the Removal of Methylene Blue and Aluminum (III) from Their Aqueous Solution. Ind. Crops Prod. 170, 113687. doi:10.1016/j.indcrop.2021.113687

CrossRef Full Text | Google Scholar

Yu, D., Wang, Y., Wu, M., Zhang, L., Wang, L., and Ni, H. (2019). Surface Functionalization of Cellulose with Hyperbranched Polyamide for Efficient Adsorption of Organic Dyes and Heavy Metals. J. Clean. Prod. 232, 774–783. doi:10.1016/j.jclepro.2019.06.024

CrossRef Full Text | Google Scholar

Yu, H. F., Fu, G. Q., Liu, L., and He, B. L. (2006). Facile Synthesis and Adsorption Properties of Phosphonated Cellulose Beads for Selective Removal of Low-Density Lipoprotein. Chin. Chem. Lett. 17, 1193–1196.

Google Scholar

Zaman, A., Orasugh, J. T., Banerjee, P., Dutta, S., Ali, M. S., Das, D., et al. (2020). Facile One-Pot In-Situ Synthesis of Novel Graphene Oxide-Cellulose Nanocomposite for Enhanced Azo Dye Adsorption at Optimized Conditions. Carbohydr. Polym. 246, 116661. doi:10.1016/j.carbpol.2020.116661

PubMed Abstract | CrossRef Full Text | Google Scholar

Zhang, M., and Akbulut, M. (2011). Adsorption, Desorption, and Removal of Polymeric Nanomedicine on and from Cellulose Surfaces: Effect of Size. Langmuir 27, 12550–12559. doi:10.1021/la202287k

PubMed Abstract | CrossRef Full Text | Google Scholar

Zhang, W., Li, C., Liang, M., Geng, Y., and Lu, C. (2010). Preparation of Carboxylate-Functionalized Cellulose via Solvent-Free Mechanochemistry and its Characterization as a Biosorbent for Removal of Pb²⁺ from Aqueous Solution. J. Hazard. Mater. 181, 468–473. doi:10.1016/j.jhazmat.2010.05.036

PubMed Abstract | CrossRef Full Text | Google Scholar

Zhang, W., Wang, X.-c., Wang, J.-j., and Zhang, L.-l. (2019). Drugs Adsorption and Release Behavior of Collagen/Bacterial Cellulose Porous Microspheres. Int. J. Biol. Macromolecules 140, 196–205. doi:10.1016/j.ijbiomac.2019.08.139

CrossRef Full Text | Google Scholar

Zhao, B., Jiang, H., Lin, Z., Xu, S., Xie, J., and Zhang, A. (2019). Preparation of Acrylamide/Acrylic Acid Cellulose Hydrogels for the Adsorption of Heavy Metal Ions. Carbohydr. Polym. 224, 115022. doi:10.1016/j.carbpol.2019.115022

PubMed Abstract | CrossRef Full Text | Google Scholar

Zhao, L., Li, S., Liang, C., Qiao, L., and Du, K. (2021). High-Strength and Low-Crystallinity Cellulose/Agarose Composite Microspheres: Fabrication, Characterization and Protein Adsorption. Biochem. Eng. J. 166, 107826. doi:10.1016/j.bej.2020.107826

CrossRef Full Text | Google Scholar

Zhao, Y., Huang, M., Wu, W., and Jin, W. (2009). Synthesis of the Cotton Cellulose Based Fe(III)-Loaded Adsorbent for Arsenic(V) Removal from Drinking Water. Desalination 249, 1006–1011. doi:10.1016/j.desal.2009.09.015

CrossRef Full Text | Google Scholar

Zhao, Y., Li, X., Liu, L., and Chen, F. (2008). Fluoride Removal by Fe(III)-Loaded Ligand Exchange Cotton Cellulose Adsorbent from Drinking Water. Carbohydr. Polym. 72, 144–150. doi:10.1016/j.carbpol.2007.07.038

CrossRef Full Text | Google Scholar

Zheng, X., Zhang, Y., Bian, T., Zhang, Y., Li, Z., and Pan, J. (2020). Oxidized Carbon Materials Cooperative Construct Ionic Imprinted Cellulose Nanocrystals Films for Efficient Adsorption of Dy(III). Chem. Eng. J. 381, 122669. doi:10.1016/j.cej.2019.122669

CrossRef Full Text | Google Scholar

Zhu, H.-Y., Fu, Y.-Q., Jiang, R., Jiang, J.-H., Xiao, L., Zeng, G.-M., et al. (2011). Adsorption Removal of congo Red onto Magnetic cellulose/Fe₃O₄/activated Carbon Composite: Equilibrium, Kinetic and Thermodynamic Studies. Chem. Eng. J. 173, 494–502. doi:10.1016/j.cej.2011.08.020

CrossRef Full Text | Google Scholar