Jane Ru Choi1,2*- 1Centre for Blood Research, Life Sciences Centre, University of British Columbia, Vancouver, BC, Canada
- 2Department of Mechanical Engineering, University of British Columbia, Vancouver, BC, Canada
Coronavirus disease 2019 (COVID-19) outbreak has become a global pandemic. The deleterious effects of coronavirus have prompted the development of diagnostic tools to manage the spread of disease. While conventional technologies such as quantitative real time polymerase chain reaction (qRT-PCR) have been broadly used to detect COVID-19, they are time-consuming, labor-intensive and are unavailable in remote settings. Point-of-care (POC) biosensors, including chip-based and paper-based biosensors are typically low-cost and user-friendly, which offer tremendous potential for rapid medical diagnosis. This mini review article discusses the recent advances in POC biosensors for COVID-19. First, the development of POC biosensors which are made of polydimethylsiloxane (PDMS), papers, and other flexible materials such as textile, film, and carbon nanosheets are reviewed. The advantages of each biosensors along with the commercially available COVID-19 biosensors are highlighted. Lastly, the existing challenges and future perspectives of developing robust POC biosensors to rapidly identify and manage the spread of COVID-19 are briefly discussed.
Introduction
Coronavirus disease 2019 (COVID-19) is an infectious illness caused by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) (Chen L. et al., 2020; Hu et al., 2020). On 20 January 2020, World Health Organization (WHO) declared the outbreak of COVID-19 a global public health emergency of international concern (Zheng et al., 2020). The incidence of COVID-19 has increased drastically, with more than three million cases reported worldwide, causing more than 200,000 deaths (Baud et al., 2020). The clinical manifestation of COVID-19 ranges from mild illnesses such as fever, cough and dyspnea to life-threatening syndromes, including pneumonia, acute respiratory distress syndrome, or even death (Bedford et al., 2020; Bernheim et al., 2020). COVID-19 has high transmission capability, making the prevention and control difficult (Chen S. et al., 2020). As there is no specific antiviral treatment or vaccine for COVID-19, early and prompt diagnosis is important to reduce the risk of life-threatening complications and mortality through appropriate health care (Lee et al., 2020; Xiao and Torok, 2020).
With the advances in POC testing, chip-based [e.g., polydimethylsiloxane (PDMS) biosensors] and paper-based biosensors [e.g., lateral flow test strips or three-dimensional (3D) paper-based microfluidic biosensors] have been developed for rapid diagnosis of infectious diseases (Choi et al., 2017; Yew et al., 2018; Zhang et al., 2019). They are widely used to detect antibodies, antigens or nucleic acids in crude samples such as saliva, sputum, and blood based upon colorimetric, fluorescent, or electrochemical detection approaches (Choi et al., 2015; Tang et al., 2017a; Yee et al., 2018). They offer many advantages such as being Affordable, Sensitive, Specific, User-friendly, Rapid and Robust, Equipment-free, and Deliverable to end users (ASSURED) (Gong et al., 2017; Tomás et al., 2019). The result can be obtained in a fast and simple manner, which allows rapid decision-making, hence minimizes the risk of human-to-human transmission.
In view of the escalating demand for rapid diagnosis of COVID-19, a mini review that summarizes the recent progress in developing POC biosensors for COVID-19 is highly desirable. In this review article, the most recent advances in POC biosensors, including both chip-based or paper-based biosensors for the detection of COVID-19 infection are reviewed. The advantages of each biosensors along with the commercially available COVID-19 biosensors are summarized. Finally, the existing challenges and future perspectives of developing robust and fully integrated POC biosensors for COVID-19 are briefly discussed.
Development of Point-of-Care Biosensors for COVID-19
In general, there are two types of rapid POC tests that can detect COVID-19 infections, which are nucleic acid and antibody (Ab) tests (Sheridan, 2020). The nucleic acid test is usually performed by detecting the presence of virus in patient's sputum (or saliva) or nasal secretions (snot) (Zhifeng et al., 2020). Such test is good at detecting the virus at early stage of infection or even before the symptoms appear. On the other hand, the antibody test strip (IgG/IgM test) is performed by collecting patient blood samples that contain antibodies against the virus (Li et al., 2020). In general, about 5 days after initial infection, the virus triggers the immune response which stimulates the production of both IgM and IgG in blood that fight against the virus (Thevarajan et al., 2020). These antibodies can be detected in patient plasma, serum or whole blood. The existing POC biosensors and commercial products for COVID-19 are summarized in Table 1. In fact, compared to the existing POC biosensors, quantitative real-time polymerase chain reaction (qRT-PCR), the gold standard for COVID-19, shows a higher clinical sensitivity and specificity, which are 79–96.7 and 100%, respectively (He et al., 2020). The clinical sensitivity and specificity of commercial POC biosensor (i.e., IgG/IgM lateral flow test strip) are 86.43–93.75 and 90.63–100%, respectively. The POC biosensors which are potentially used for COVID-19 are sample-to-answer chip-based biosensors, paper-based biosensors or other material-based biosensors (Figure 1) which are briefly discussed in the following sections.
Table 1. Point-of-care biosensors and commercial products for COVID-19.
Figure 1. Point-of-care biosensors for COVID-19. Respiratory and blood samples are collected for the detection of viral nucleic acids and human antibodies against the virus. Point-of-care biosensors such as chip-based biosensors (Ma et al., 2019), paper-based biosensors (Li et al., 2020), film-based biosensors (Kukhtin et al., 2019), thread-based biosensors (Choi et al., 2018a), graphene-based biosensors (Kampeera et al., 2019), and black phosphorus-based biosensors (Kumar et al., 2016) offer tremendous potential for identifying and managing the spread of COVID-19. Rapid onsite analysis can be performed using a smartphone for appropriate health management.
Chip-Based Biosensors
Chip-based biosensors have been broadly used for point-of-care diagnosis of infectious diseases. They are mainly made of PDMS or poly(methyl methacrylate) (PMMA) (Zarei, 2017a; Zhang et al., 2017). These biosensors allow automated, precise manipulation of fluid flow with small volume of samples. They are able to minimize reagent consumption which enables high throughput analysis (Dincer et al., 2017; Nasseri et al., 2018). PDMS chip-based biosensors, in particular, have attracted scientific interest due to its biocompatibility, high transparency and cost-effectiveness (Nayak et al., 2017). They have been explored in both antibodies and nucleic acid detection for monitoring infectious diseases (Wang et al., 2016; Darwish et al., 2018). Recent studies have focused on the development of sample-to-answer platform for nucleic acid testing as they are more sensitive and specific than antibody assays. For example, a study has developed a sample-to-answer “lab-on-a-disc” biosensor (Loo et al., 2017). This PDMS-based biosensor consists of multiple channels that allows automated nucleic acid extraction, isothermal amplification [loop-mediated isothermal amplification (LAMP)] and real time signal detection. SYTO-9 dye is used for detection, which binds to the double-stranded DNA from LAMP reaction and emits green fluorescence. The intensity of fluorescence signal indicates the amount of target detected. The biosensor is self-contained for performing sample heating and chemical lysis for both extraction and amplification processes. The entire sample-to-answer processes take ~2 h. While the platform is portable, the size of biosensor is relatively large, which requires further improvement. The biosensor can be readily customized to detect COVID-19 viruses in the near future.
More recently, one group has integrated digital amplification process into a sample-to-answer chip-based biosensor to quantify nucleic acids which further simplifies the entire process of nucleic acid testing (Yin et al., 2020). The biosensor integrates nucleic acid extraction, multiplex digital recombinase polymerase amplification (RPA) and fluorescence detection into a single biosensor. It is mainly made of PDMS layers with a glass slide as a supporting substrate. The specific primer mixture and all of the reaction solution for RPA except magnesium acetate are added onto three different detection areas and lyophilized. Once the sample is added, the cell is lysed and the nucleic acids bind to the magnetic beads. Following the washing and elution steps, the reagents are passively driven into the digital RPA area using vacuum-based self-priming approaches for isothermal amplification, followed by fluorescent imaging. As the fluorescence probe is labeled with carboxyfluorescein (FAM) which is detectable by the UV light, the fluorescence signal intensity is proportional to the concentration of amplicons. The biosensor could achieve three main steps of nucleic acid testing within 45 min without requiring complex instrument and control systems. This integrated biosensor shows immense potential to rapidly and accurately detect COVID-19 in patient samples.
Besides fluorescence signal detection, colorimetric detection approach has also been used in chip-based biosensors. The output of isothermal amplification (e.g., LAMP) has been visualized by colorimetric indicators [e.g., calcein or hydroxynaphthol blue (HNB)] that interact with amplicons or byproducts (i.e., pyrophosphate; Seok et al., 2017; Quyen et al., 2019; Wang et al., 2019). Calcein binds manganese ions that quench fluorescence and the complex interacts with pyrophosphate to express fluorescent signal (Dou et al., 2019). HNB changes color from violet to sky blue upon reacting with pyrophosphate (Yang et al., 2018). To improve the portability and functionality of chip-based biosensors, one has developed an automated, portable sample-to-answer biosensor coupled with a smartphone for colorimetric detection of pathogens (Ma et al., 2019). It consists of a microfluidic structure layer, a hydrophilic layer, a PDMS hydrophobic layer and a glass substrate. The biosensor is able to (i) purify pathogens with specific affinity reagent pre-conjugated to magnetic beads, (ii) conduct lysis at low temperatures, (iii) perform LAMP, and (iv) quantify the results based on colorimetric signals. HNB is used as an indicator or visual dye for amplicons. As mentioned, the LAMP reaction changes the color of LAMP products from violet to sky blue. The entire process is about 40 min which is automatically performed and being monitored using a smartphone. Future work should include storing the reagents on chip to make it more applicable at remote settings.
Paper-Based Biosensors
Paper-based biosensors have attracted more significant attention for use in POC testing as compared to chip-based biosensors owing to their cost-effectiveness, biodegradability as well as ease-of-fabrication, functionalization and modification (Hu et al., 2017; Böhm et al., 2018; Choi et al., 2019). With these characteristics, they are able to achieve rapid, onsite POC testing in remote settings (Tang et al., 2017b). Lateral flow test strips, in particular, have been widely used for the detection of COVID-19. They are designed to detect IgG and IgM in patient whole blood, serum and plasma samples (Li et al., 2020; Sheridan, 2020). Each test strip generally consists of (i) a sample pad to add patient samples, (ii) a conjugate pad containing COVID-19 antigen conjugated with gold nanoparticles (gold-COVID-19) and gold-rabbit IgG, (iii) a nitrocellulose membrane that consists of a control line coated with goat anti-rabbit IgG, an IgG test line coated with anti-human IgG, an IgM test line coated with anti-human IgM as well as (iv) an absorbent pad that absorbs waste (Li et al., 2020; Sheridan, 2020). In the presence of IgM and/or IgG in patient samples, the antibodies react with gold-COVID-19 antigen to form a complex, which moves across the nitrocellulose membrane and interact with the anti-IgM and/or IgG at their respective test line. The gold-rabbit IgG in turn reacts with anti-rabbit IgG coated at the control line to produce a visible red color. A positive IgM and a negative IgG or positive at both lines indicate a primary or acute infection, while a positive IgG with a negative IgM shows a secondary or later stage of infection (Du et al., 2020; Li et al., 2020).
Apart from antibody testing, some lateral flow test strips with sample-to-answer capability have been used for nucleic acid testing which could potentially detect COVID-19 nucleic acids in respiratory samples. For instance, a group has introduced a fully integrated paper-based biosensor that involves three main steps of nucleic acid testing (i.e., nucleic acid extraction, LAMP, and detection), producing colorimetric signal detected by lateral flow test strip (Rodriguez et al., 2016). However, this integrated biosensor requires an external heat block for amplification. To simplify the platform for POC applications, a small and portable heater has been developed in combination with four-layered paper-based sample-to-answer biosensor (Choi et al., 2016a). This biosensor consists of Fast Technology Analysis (FTA) card and glass fiber for nucleic acid extraction and LAMP, along with an integrated lateral flow test strip for visual detection. Each functional layer is separated by hydrophobic polyvinyl chloride substrates that control the fluid flow from one layer to another. To further simplify the processes, a semi-automated, fully disposable and integrated paper-based biosensor has been developed (Tang et al., 2017c). This integrated biosensor consists of a paper-based valve and a sponge-based reservoir to extract nucleic acids from crude samples, a portable battery and a heater integrated into the platform for isothermal amplification (i.e., helicase dependent amplification, HDA) as well as a lateral flow test strip for colorimetric detection. The proposed biosensor allows on board reagent storage with the use of sponges and equipment-free isothermal amplification which significantly simplifies user steps. More recently, lateral flow test strip has been combined with paper folding technologies for sample preparation, LAMP and lateral flow detection (Reboud et al., 2019). The integrated test strip consists of buffer chambers that regulate fluid flow, acetate films which prevent sample evaporation, filter paper-based valves that prevent LAMP reagent from mixing with other reagents, and a lateral flow test strip. This integrated technology is suitable for use in resource-limited settings to test crude samples (e.g., sputum), offering great potential to rapidly detect nucleic acids of COVID-19 (<50 min).
Besides lateral flow test strips, several 3D paper-based microfluidic biosensors have been developed to detect proteins or nucleic acids at the POC (Xia et al., 2016; Lam et al., 2017). These biosensors usually detect targets based on fluorescence or colorimetric detection approaches. Metal ions (e.g., magnesium, calcium, or silver) have been used in 3D paper-based microfluidic biosensors to react with base (purine or pyrimidine) from double stranded DNA to form a stable complex that show fluorescent signal upon UV irradiation. For example, a fully integrated and foldable biosensor encapsulated with agarose have been developed for long-term reagent storage and multiplex fluorescence detection (Trinh et al., 2019). The biosensor consists of a reaction zone and a detection zone. Agarose that carries LAMP reagents and silver nitrate (reaction indicator) is deposited and stored in reaction and detection zones for at least 45 days. The sample is added into reaction zones which are then closed with an adhesive sealing film to avoid sample evaporation before being placed on a portable heater for amplification. Following the amplification process, the sealing film is removed and the detection zone is folded and soaked into the reaction zone. UV light is used to visualize the reaction between amplicons and silver ions. The brown color intensity of the test zone increased along with the increased concentration of amplicons. The biosensor is simple and user friendly, which is expected to detect COVID-19 nucleic acids in patient samples.
More recently, as a new alternative, fuchsin has been explored for the detection of DNA amplicons based upon colorimetric detection approach using a 3D paper-based microfluidic biosensor (Trinh and Lee, 2019). In the absence of DNA amplicons, addition of sodium sulfite molecule and fushsin produces fushsin leucosulfonic acid or leucofushsin which is colorless. In the presence of DNA amplicons, aldehyde groups of the DNA bind to sulfonate groups and the bond between hydrogen sulfite and the central C atom is broken, producing the fuchsin with chromophoric structure, which appears to be purple signals (Mello and de Campos Vidal, 2017). The proposed biosensor is composed of a sample zone, a reaction zone and a detection zone. The detection zone consists of paper strips with fuchsin stained lines. Briefly, sample is injected into the sample zone which is sealed with an adhesive sealing film to prevent sample evaporation. The reaction zone is folded to bind to the sample zone and the biosensor is turned upside down to enable the flow of sample from sample zone to reaction zone. The biosensor is heated on a hot plate at 65°C for 30 min for LAMP. After LAMP, the sealing film is peeled off and the hydrochloric acid is injected into the reaction zone. Sodium sulfite is subsequently added and the changes of fuchsin-stained line color is observed. Unlike the above-mentioned biosensors, this biosensor produces simple colorimetric signals detectable by the naked eyes without requiring any external readers, which shows promising for rapid diagnosis of COVID-19 infections at the POC.
Other Biosensors
Apart from developing chip-based and paper-based biosensors, other material-based biosensors such as textile-based, film-based or carbon-based biosensors have also been introduced for potential use for COVID-19 (Parrilla et al., 2016; Afsahi et al., 2018; Mogha et al., 2018). They are developed to improve the functionality and detection sensitivity of the existing biosensors, providing more promising choices for practical use. Textile-based biosensors such as thread-based, fabric-based or cloth-based biosensors have been developed with simple fabrication processes and improved assay performance. One study has incorporated polysiloxanes with tunable hydrophobicity into thread-based biosensors to delay fluid flow in lateral flow assay and improve detection sensitivity (Choi et al., 2018a). Similar to conventional lateral flow test strip, the fluidic delay in thread increases interactions between gold nanoparticles-antibodies (AuNP-Ab) and targets. With the optimum conditions, the increase in interactions produces more AuNP-Ab-target complexes, showing 10-fold more sensitive than the unmodified biosensors. This biosensor is simple-to-fabricate and highly sensitive, which shows immense potential in detecting IgG and IgM in COVID-19 patients for appropriate health monitoring.
In addition to textile-based biosensors, film-based biosensors have been developed to detect infectious microorganism from crude samples. For instance, a film-based biosensor has been introduced which consists of a transparent polyester film substrate, a sample chamber, a cover, a reaction chamber and a waste chamber (Kukhtin et al., 2019). Microarray 2-(hydroxyethyl)methacrylamide gel elements are synthesized with the incorporation of oligonucleotides into gels and polymerization under UV irradiation. The gel elements are covalently attached to the substrate. Briefly, both sample and master mix are first introduced into chambers. The capillary action promotes uniform filling of the chamber and amplification is subsequently performed. Wash buffer is then introduced and the pressure leads the waste to the waste chambers. Lastly, fluorescent imaging and analysis are performed. The flexible film substrate used in the study offers several advantages for POC testing: (i) allows covalent attachment of gel without pre-treatment processes, (ii) has low background fluorescence, (iii) has transparent properties that allows optical inspection, (iv) able to withstand thermal cycling and compatible to amplification processes. This flexible film allows easy fabrication and is user-friendly, which costs ~500 times less than other substrates (i.e., glass), demonstrating its potential for detecting COVID-19 virus in patient samples.
Apart from these, 2D materials such as graphene or black phosphorus have also been integrated into biosensors for POC diagnosis which could potentially be used for COVID-19 testing (Jin et al., 2017; Choi et al., 2018b; Liu et al., 2018). For example, a recent study has introduced a portable graphene-based electrochemical biosensor for highly sensitive POC testing (Kampeera et al., 2019). Graphene-based electrodes are constructed by screen-printing mainly due to low cost, ease of fabrication and high production rate. The screen-printed graphene electrodes (SPGE) are synthesized by either substituting carbon with graphene or incorporating graphene into carbon paste. SPGE have been reported to show superior electrochemical properties than commonly used screen-printed carbon electrodes (SPCE) by having a higher electron transfer rate and a larger electrochemical surface area. After nucleic acid extraction, LAMP is performed using a simple heating block. The interaction between SPGE and amplicons results in a shift in cathodic current which stems from the intercalation of redox probe to double-stranded DNA. This phenomenon enables quantification of LAMP product. A portable mini potentiostat is used in combination with SPGE for on-site detection. The next step should be the integration of extraction platform into the proposed biosensor to make it more portable and user-friendly.
Besides graphene, black phosphorus (BP) or phosphorene-based biosensors have also been extensively explored for medical diagnosis (Qian et al., 2017; Ge et al., 2019; Luo et al., 2019). BP displays excellent electrochemical properties which enhances assay sensitivity and selectivity owing to its inherent redox properties. For example, a recent study has reported the development of a label-free electrochemical biosensor with an aptamer-functionalized BP nanostructured electrode (Kumar et al., 2016). The BP nanosheets are coated with poly-L-lysine (PLL) that allows functionalization of BP with antiAb-aptamers. The aptamers are immobilized onto the nanosheets via the coulomb interaction between aptamers and PLL. The presence of target antigens causes the direct oxidization of iron (ii) to iron (iii) at the electrode surface through the mechanism of electron transfer. As compared to reduced graphene oxide (rGO), BP-based biosensors show a higher detection sensitivity and specificity, achieving the detection limit down to pg level compared to ng level achieved by rGO biosensors. The proposed biosensor would allow highly sensitive detection of IgG or IgM against coronavirus in patient blood samples.
Conclusion and Future Perspectives
In summary, this review article discusses the POC biosensors that made of PDMS, paper and other flexible materials such as textile, film, and carbon nanosheets for rapid diagnosis of COVID-19. The cost-effectiveness, simplicity, rapidity and portability of these biosensors play a crucial role in POC applications. Antibody tests are suitable to detect the late stage of infections while nucleic acid tests detect the presence of nucleic acids (viruses) at the early stage of infection, showing a higher sensitivity and specificity than antibody tests. However, current nucleic acid tests require three key steps (i.e., nucleic acid extraction, amplification, and detection), involving more complicated processes than that of antibody tests. In fact, most of the commercial POC biosensors for COVID-19 are paper-based biosensors or lateral flow test strips for antibody detection (IgG and IgM) that produce colorimetric signal. While these antibody tests display lower specificity compared to nucleic acid tests, they have helped shortening the turnaround time for rapid diagnosis, allowing fast decision making. Future work should include specificity improvement or combination with other tests such as rapid nucleic acid tests to further confirm the test result.
Recent studies have integrated sample-to-answer processes into a single biosensor to detect nucleic acids of pathogens and human antibodies against the pathogens, which could be further explored to detect COVID-19 infections. In addition, current works have also attempted to improve detection sensitivity, simplicity and performance of biosensors. Assay sensitivity can be enhanced through enzyme-based signal enhancement (He et al., 2011), sample concentration (Moghadam et al., 2015) or much simpler fluidic-control strategies (Choi et al., 2016b). Further, nucleic acid tests, in particular, that involves three key steps should be simplified and integrated into a single biosensor for POC use. The biosensors discussed in this review show immense potential to be developed into a self-contained platform for the detection of COVID-19 infections outside the laboratory, particularly in the remote settings or developing areas.
In the future, more studies should focus on simplifying user steps and incorporating all key steps into a single biosensor at minimal cost (Loo et al., 2019). The capability of storing all reagents on chip is vital to eliminate the requirement for large storage equipment (Deng and Jiang, 2019) whereas, the multiplexing capability of biosensors would increase throughput (Dincer et al., 2017). As compared to other detection approaches such as fluorescence and electrochemical detection approaches, colorimetric detection represents the most common approach mainly due to its simplicity and the ability to observe signal with the naked eyes. The biosensors that produce colorimetric signals enable visual detection without requiring extra tools such as UV lamp, which would be helpful for rapid on-site diagnosis (Chan et al., 2016; Yang et al., 2019). Quantification, which provides more accurate readout has been achieved using smartphone apps which could be performed by untrained users at POC settings. Future studies should further improve the function of smartphone and specific smartphone apps that enable on-site data analysis while allowing data storage to track patient health status (Roda et al., 2016; Wang et al., 2017; Liang et al., 2019; Xu et al., 2020). Additionally, incorporating portable power sources such as batteries into biosensors would significantly advance their functionality especially in rural areas where electricity supply is limited (Zarei, 2017b). In short, emerging POC biosensors with the aforementioned capabilities could rapidly identify the spread of COVID-19 and guide appropriate health care, playing a key role in managing the outbreak.
Author Contributions
The author confirms being the sole contributor of this work and has approved it for publication.
Funding
JC is supported by Michael Smith Foundation for Health Research (17982).
Conflict of Interest
The author declares that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest.
References
Afsahi, S., Lerner, M. B., Goldstein, J. M., Lee, J., Tang, X., Bagarozzi, D. A. Jr., et al. (2018). Novel graphene-based biosensor for early detection of Zika virus infection. Biosens. Bioelectr. 100, 85–88. doi: 10.1016/j.bios.2017.08.051
Baud, D., Qi, X., Nielsen-Saines, K., Musso, D., Pomar, L., and Favre, G. (2020). Real estimates of mortality following COVID-19 infection. Lancet Infect. Dis. doi: 10.1016/S1473-3099(20)30195-X. [Epub ahead of print].
Bedford, J., Enria, D., Giesecke, J., Heymann, D. L., Ihekweazu, C., Kobinger, G., et al. (2020). COVID-19: towards controlling of a pandemic. Lancet 395, 1015–1018. doi: 10.1016/S0140-6736(20)30673-5
Bernheim, A., Mei, X., Huang, M., Yang, Y., Fayad, Z. A., Zhang, N., et al. (2020). Chest CT findings in coronavirus disease-19 (COVID-19): relationship to duration of infection. Radiology 295, 685–691. doi: 10.1148/radiol.2020200463
Böhm, A., Trosien, S., Avrutina, O., Kolmar, H., and Biesalski, M. (2018). Covalent attachment of enzymes to paper fibers for paper-based analytical devices. Front. Chem. 6:214. doi: 10.3389/fchem.2018.00214
Chan, H. N., Shu, Y., Xiong, B., Chen, Y., Chen, Y., Tian, Q., et al. (2016). Simple, cost-effective 3D printed microfluidic components for disposable, point-of-care colorimetric analysis. ACS Sensors 1, 227–234. doi: 10.1021/acssensors.5b00100
Chen, L., Xiong, J., Bao, L., and Shi, Y. (2020). Convalescent plasma as a potential therapy for COVID-19. Lancet Infect. Dis. 20, 398–400. doi: 10.1016/S1473-3099(20)30141-9
Chen, S., Yang, J., Yang, W., Wang, C., and Bärnighausen, T. (2020). COVID-19 control in China during mass population movements at New Year. Lancet 395, 764–766. doi: 10.1016/S0140-6736(20)30421-9
Choi, J. R., Hu, J., Tang, R., Gong, Y., Feng, S., Ren, H., et al. (2016a). An integrated paper-based sample-to-answer biosensor for nucleic acid testing at the point of care. Lab Chip 16, 611–621. doi: 10.1039/C5LC01388G
Choi, J. R., Hu, J., Wang, S., Yang, H., Wan Abas, W. A. B., Pingguan-Murphy, B., et al. (2017). Based point-of-care testing for diagnosis of dengue infections. Crit. Rev. Biotechnol. 37, 100–111. doi: 10.3109/07388551.2016.1139541
Choi, J. R., Liu, Z., Hu, J., Tang, R., Gong, Y., Feng, S., et al. (2016b). Polydimethylsiloxane-paper hybrid lateral flow assay for highly sensitive point-of-care nucleic acid testing. Anal. Chem. 88, 6254–6264. doi: 10.1021/acs.analchem.6b00195
Choi, J. R., Nilghaz, A., Chen, L., Chou, K. C., and Lu, X. (2018a). Modification of thread-based microfluidic device with polysiloxanes for the development of a sensitive and selective immunoassay. Sensors Actuat. B 260, 1043–1051. doi: 10.1016/j.snb.2018.01.102
Choi, J. R., Tang, R., Wang, S., Abas, W. A. B. W., Pingguan-Murphy, B., and Xu, F. (2015). Paper-based sample-to-answer molecular diagnostic platform for point-of-care diagnostics. Biosens. Bioelectr. 74, 427–439. doi: 10.1016/j.bios.2015.06.065
Choi, J. R., Yong, K. W., Choi, J. Y., and Cowie, A. C. (2019). Emerging point-of-care technologies for food safety analysis. Sensors 19:817. doi: 10.3390/s19040817
Choi, J. R., Yong, K. W., Choi, J. Y., Nilghaz, A., Lin, Y., Xu, J., et al. (2018b). Black phosphorus and its biomedical applications. Theranostics 8:1005. doi: 10.7150/thno.22573
Darwish, N. T., Sekaran, S. D., and Khor, S. M. (2018). Point-of-care tests: a review of advances in the emerging diagnostic tools for dengue virus infection. Sensors Actuat. B 255, 3316–3331. doi: 10.1016/j.snb.2017.09.159
Deng, J., and Jiang, X. (2019). Advances in reagents storage and release in self-contained point-of-care devices. Adv. Mater. Technol. 4:1800625. doi: 10.1002/admt.201800625
Dincer, C., Bruch, R., Kling, A., Dittrich, P. S., and Urban, G. A. (2017). Multiplexed point-of-care testing–xPOCT. Trends Biotechnol. 35, 728–742. doi: 10.1016/j.tibtech.2017.03.013
Dou, M., Sanchez, J., Tavakoli, H., Gonzalez, J. E., Sun, J., Bard, J. D., et al. (2019). A low-cost microfluidic platform for rapid and instrument-free detection of whooping cough. Anal. Chim. Acta 1065, 71–78. doi: 10.1016/j.aca.2019.03.001
Du, Z., Zhu, F., Guo, F., Yang, B., and Wang, T. (2020). Detection of antibodies against SARS-CoV-2 in patients with COVID-19. J. Med. Virol. doi: 10.1002/jmv.25820. [Epub ahead of print].
Ge, X., Xia, Z., and Guo, S. (2019). Recent advances on black phosphorus for biomedicine and biosensing. Adv. Funct. Mater. 29:1900318. doi: 10.1002/adfm.201900318
Gong, Y., Hu, J., Choi, J. R., You, M., Zheng, Y., Xu, B., et al. (2017). Improved LFIAs for highly sensitive detection of BNP at point-of-care. Int. J. Nanomed. 12:4455. doi: 10.2147/IJN.S135735
He, J.-L., Luo, L., Luo, Z.-D., Lyu, J.-X., Ng, M.-Y., Shen, X.-P., et al. (2020). Diagnostic performance between CT and initial real-time RT-PCR for clinically suspected 2019 coronavirus disease (COVID-19) patients outside Wuhan, China. Respir. Med. 168:105980. doi: 10.1016/j.rmed.2020.105980
He, Y., Zhang, S., Zhang, X., Baloda, M., Gurung, A. S., Xu, H., et al. (2011). Ultrasensitive nucleic acid biosensor based on enzyme–gold nanoparticle dual label and lateral flow strip biosensor. Biosens. Bioelectr. 26, 2018–2024. doi: 10.1016/j.bios.2010.08.079
Hu, J., Choi, J. R., Wang, S., Gong, Y., Feng, S., Pingguan-Murphy, B., et al. (2017). Multiple test zones for improved detection performance in lateral flow assays. Sensors Actuat. B 243, 484–488. doi: 10.1016/j.snb.2016.12.008
Hu, T. Y., Frieman, M., and Wolfram, J. (2020). Insights from nanomedicine into chloroquine efficacy against COVID-19. Nat. Nanotechnol. 15:247–249. doi: 10.1038/s41565-020-0674-9
Jin, S.-A., Marinero, E. E., Stanciu, L. A. S., Poudyal, S., and Kuhn, R. J. (2017). Impedimetric zika and dengue biosensor based on functionalized graphene oxide wrapped silica particles. Bull. Am. Phys. Soc. 62:116. doi: 10.1016/j.electacta.2016.02.116
Kampeera, J., Pasakon, P., Karuwan, C., Arunrut, N., Sappat, A., Sirithammajak, S., et al. (2019). Point-of-care rapid detection of Vibrio parahaemolyticus in seafood using loop-mediated isothermal amplification and graphene-based screen-printed electrochemical sensor. Biosens. Bioelectr. 132, 271–278. doi: 10.1016/j.bios.2019.02.060
Kukhtin, A. C., Sebastian, T., Golova, J., Perov, A., Knickerbocker, C., Linger, Y., et al. (2019). Lab-on-a-Film disposable for genotyping multidrug-resistant Mycobacterium tuberculosis from sputum extracts. Lab Chip 19, 1217–1225. doi: 10.1039/C8LC01404C
Kumar, V., Brent, J. R., Shorie, M., Kaur, H., Chadha, G., Thomas, A. G., et al. (2016). Nanostructured aptamer-functionalized black phosphorus sensing platform for label-free detection of myoglobin, a cardiovascular disease biomarker. ACS Appl. Mater. Interfaces 8, 22860–22868. doi: 10.1021/acsami.6b06488
Lam, T., Devadhasan, J. P., Howse, R., and Kim, J. (2017). A chemically patterned microfluidic paper-based analytical device (C-μPAD) for point-of-care diagnostics. Sci. Rep. 7, 1–10. doi: 10.1038/s41598-017-01343-w
Lee, E. Y., Ng, M.-Y., and Khong, P.-L. (2020). COVID-19 pneumonia: what has CT taught us? Lancet Infect. Dis. 20, 384–385. doi: 10.1016/S1473-3099(20)30134-1
Li, Z., Yi, Y., Luo, X., Xiong, N., Liu, Y., Li, S., et al. (2020). Development and clinical application of a rapid IgM-IgG combined antibody test for SARS-CoV-2 infection diagnosis. J. Med. Virol. doi: 10.1002/jmv.25727. [Epub ahead of print].
Liang, C., Liu, Y., Niu, A., Liu, C., Li, J., and Ning, D. (2019). Smartphone-app based point-of-care testing for myocardial infarction biomarker cTnI using an autonomous capillary microfluidic chip with self-aligned on-chip focusing (SOF) lenses. Lab Chip 19, 1797–1807. doi: 10.1039/C9LC00259F
Liu, M., Zhang, Q., Brennan, J. D., and Li, Y. (2018). Graphene-DNAzyme-based fluorescent biosensor for Escherichia coli detection. MRS Commun. 8, 687–694. doi: 10.1557/mrc.2018.97
Loo, J., Kwok, H., Leung, C., Wu, S., Law, I., Cheung, Y., et al. (2017). Sample-to-answer on molecular diagnosis of bacterial infection using integrated lab-on-a-disc. Biosens. Bioelectr. 93, 212–219. doi: 10.1016/j.bios.2016.09.001
Loo, J. F., Ho, A. H., Turner, A. P., and Mak, W. C. (2019). Integrated printed microfluidic biosensors. Trends Biotechnol. 37, 1104–1120. doi: 10.1016/j.tibtech.2019.03.009
Luo, M., Fan, T., Zhou, Y., Zhang, H., and Mei, L. (2019). 2D black phosphorus–based biomedical applications. Adv. Funct. Mater. 29:1808306. doi: 10.1002/adfm.201808306
Ma, Y.-D., Li, K.-H., Chen, Y.-H., Lee, Y.-M., Chou, S.-T., Lai, Y.-Y., et al. (2019). A sample-to-answer, portable platform for rapid detection of pathogens with a smartphone interface. Lab Chip 19, 3804–3814. doi: 10.1039/C9LC00797K
Mello, M. L. S., and de Campos Vidal, B. (2017). The Feulgen reaction: a brief review and new perspectives. Acta Histochem. 119, 603–609. doi: 10.1016/j.acthis.2017.07.002
Mogha, N. K., Sahu, V., Sharma, R. K., and Masram, D. T. (2018). Reduced graphene oxide nanoribbon immobilized gold nanoparticle based electrochemical DNA biosensor for the detection of Mycobacterium tuberculosis. J. Mater. Chem. B 6, 5181–5187. doi: 10.1039/C8TB01604F
Moghadam, B. Y., Connelly, K. T., and Posner, J. D. (2015). Two orders of magnitude improvement in detection limit of lateral flow assays using isotachophoresis. Anal. Chem. 87, 1009–1017. doi: 10.1021/ac504552r
Nasseri, B., Soleimani, N., Rabiee, N., Kalbasi, A., Karimi, M., and Hamblin, M. R. (2018). Point-of-care microfluidic devices for pathogen detection. Biosens. Bioelectr. 117, 112–128. doi: 10.1016/j.bios.2018.05.050
Nayak, S., Blumenfeld, N. R., Laksanasopin, T., and Sia, S. K. (2017). Point-of-care diagnostics: recent developments in a connected age. Anal. Chem. 89, 102–123. doi: 10.1021/acs.analchem.6b04630
Parrilla, M., Cánovas, R., Jeerapan, I., Andrade, F. J., and Wang, J. (2016). A textile-based stretchable multi-ion potentiometric sensor. Adv. Healthc. Mater. 5, 996–1001. doi: 10.1002/adhm.201600092
Qian, X., Gu, Z., and Chen, Y. (2017). Two-dimensional black phosphorus nanosheets for theranostic nanomedicine. Mater. Horizons 4, 800–816. doi: 10.1039/C7MH00305F
Quyen, T. L., Ngo, T. A., Bang, D. D., Madsen, M., and Wolff, A. (2019). Classification of multiple DNA dyes based on inhibition effects on real-time loop-mediated isothermal amplification (LAMP): prospect for point of care setting. Front. Microbiol. 10:2234. doi: 10.3389/fmicb.2019.02234
Reboud, J., Xu, G., Garrett, A., Adriko, M., Yang, Z., Tukahebwa, E. M., et al. (2019). Paper-based microfluidics for DNA diagnostics of malaria in low resource underserved rural communities. Proc. Natl. Acad. Sci. U.S.A. 116, 4834–4842. doi: 10.1073/pnas.1812296116
Roda, A., Michelini, E., Zangheri, M., Di Fusco, M., Calabria, D., and Simoni, P. (2016). Smartphone-based biosensors: a critical review and perspectives. Trends Anal. Chem. 79, 317–325. doi: 10.1016/j.trac.2015.10.019
Rodriguez, N. M., Wong, W. S., Liu, L., Dewar, R., and Klapperich, C. M. (2016). A fully integrated paperfluidic molecular diagnostic chip for the extraction, amplification, and detection of nucleic acids from clinical samples. Lab Chip 16, 753–763. doi: 10.1039/C5LC01392E
Seok, Y., Joung, H.-A., Byun, J.-Y., Jeon, H.-S., Shin, S. J., Kim, S., et al. (2017). A paper-based device for performing loop-mediated isothermal amplification with real-time simultaneous detection of multiple DNA targets. Theranostics 7:2220. doi: 10.7150/thno.18675
Sheridan, C. (2020). Fast, portable tests come online to curb coronavirus pandemic. Nat. Biotechnol.38, 515–518. doi: 10.1038/d41587-020-00010-2
Tang, R., Yang, H., Choi, J. R., Gong, Y., Hu, J., Wen, T., et al. (2017a). based device with on-chip reagent storage for rapid extraction of DNA from biological samples. Microchim. Acta 184, 2141–2150. doi: 10.1007/s00604-017-2225-0
Tang, R., Yang, H., Choi, J. R., Gong, Y., You, M., Wen, T., et al. (2017b). Capillary blood for point-of-care testing. Crit. Rev. Clin. Lab. Sci. 54, 294–308. doi: 10.1080/10408363.2017.1343796
Tang, R., Yang, H., Gong, Y., You, M., Liu, Z., Choi, J. R., et al. (2017c). A fully disposable and integrated paper-based device for nucleic acid extraction, amplification and detection. Lab Chip 17, 1270–1279. doi: 10.1039/C6LC01586G
Thevarajan, I., Nguyen, T. H., Koutsakos, M., Druce, J., Caly, L., van de Sandt, C. E., et al. (2020). Breadth of concomitant immune responses prior to patient recovery: a case report of non-severe COVID-19. Nat. Med. 26, 453–455. doi: 10.1038/s41591-020-0819-2
Tomás, A. L., de Almeida, M. P., Cardoso, F., Pinto, M., Pereira, E., Franco, R., et al. (2019). Development of a gold nanoparticle-based lateral-flow immunoassay for pneumocystis pneumonia serological diagnosis at point-of-care. Front. Microbiol. 10:2917. doi: 10.3389/fmicb.2019.02917
Trinh, T. N. D., La, H. C., and Lee, N. Y. (2019). Fully integrated and foldable microdevice encapsulated with agarose for long-term storage potential for point-of-care testing of multiplex foodborne pathogens. ACS Sensors 4, 2754–2762. doi: 10.1021/acssensors.9b01299
Trinh, T. N. D., and Lee, N. Y. (2019). A foldable isothermal amplification microdevice for fuchsin-based colorimetric detection of multiple foodborne pathogens. Lab Chip 19, 1397–1405. doi: 10.1039/C8LC01389F
Wang, H., Ma, Z., Qin, J., Shen, Z., Liu, Q., Chen, X., et al. (2019). A versatile loop-mediated isothermal amplification microchip platform for Streptococcus pneumoniae and Mycoplasma pneumoniae testing at the point of care. Biosens. Bioelectr. 126, 373–380. doi: 10.1016/j.bios.2018.11.011
Wang, L.-J., Chang, Y.-C., Sun, R., and Li, L. (2017). A multichannel smartphone optical biosensor for high-throughput point-of-care diagnostics. Biosens. Bioelectr. 87, 686–692. doi: 10.1016/j.bios.2016.09.021
Wang, S., Chinnasamy, T., Lifson, M. A., Inci, F., and Demirci, U. (2016). Flexible substrate-based devices for point-of-care diagnostics. Trends Biotechnol. 34, 909–921. doi: 10.1016/j.tibtech.2016.05.009
Xia, Y., Si, J., and Li, Z. (2016). Fabrication techniques for microfluidic paper-based analytical devices and their applications for biological testing: a review. Biosens. Bioelectr. 77, 774–789. doi: 10.1016/j.bios.2015.10.032
Xiao, Y., and Torok, M. E. (2020). Taking the right measures to control COVID-19. Lancet Infect. Dis. 20, 523–524. doi: 10.1016/S1473-3099(20)30152-3
Xu, Z., Liu, Z., Xiao, M., Jiang, L., and Yi, C. (2020). A smartphone-based quantitative point-of-care testing (POCT) system for simultaneous detection of multiple heavy metal ions. Chem. Eng. J. 394:124966. doi: 10.1016/j.cej.2020.124966
Yang, J., Wang, K., Xu, H., Yan, W., Jin, Q., and Cui, D. (2019). Detection platforms for point-of-care testing based on colorimetric, luminescent and magnetic assays: a review. Talanta 202, 96–110. doi: 10.1016/j.talanta.2019.04.054
Yang, Z., Xu, G., Reboud, J., Ali, S. A., Kaur, G., McGiven, J., et al. (2018). Rapid veterinary diagnosis of bovine reproductive infectious diseases from semen using paper-origami DNA microfluidics. ACS Sensors 3, 403–409. doi: 10.1021/acssensors.7b00825
Yee, M. F., Emmel, G. N., Yang, E. J., Lee, E., Paek, J. H., Wu, B. M., et al. (2018). Ionic liquid aqueous two-phase systems for the enhanced paper-based detection of transferrin and escherichia coli. Front. Chem. 6:486. doi: 10.3389/fchem.2018.00486
Yew, C.-H. T., Azari, P., Choi, J. R., Li, F., and Pingguan-Murphy, B. (2018). Electrospin-coating of nitrocellulose membrane enhances sensitivity in nucleic acid-based lateral flow assay. Anal. Chim. Acta 1009, 81–88. doi: 10.1016/j.aca.2018.01.016
Yin, J., Zou, Z., Hu, Z., Zhang, S., Zhang, F., Wang, B., et al. (2020). A “sample-in-multiplex-digital-answer-out” chip for fast detection of pathogens. Lab Chip 20, 979–986. doi: 10.1039/C9LC01143A
Zarei, M. (2017a). Advances in point-of-care technologies for molecular diagnostics. Biosens. Bioelectr. 98, 494–506. doi: 10.1016/j.bios.2017.07.024
Zarei, M. (2017b). Portable biosensing devices for point-of-care diagnostics: recent developments and applications. Trends Anal. Chem. 91, 26–41. doi: 10.1016/j.trac.2017.04.001
Zhang, H., Xu, Y., Fohlerova, Z., Chang, H., Iliescu, C., and Neuzil, P. (2019). LAMP-on-a-chip: Revising microfluidic platforms for loop-mediated DNA amplification. Trends Anal. Chem. 113, 44–53. doi: 10.1016/j.trac.2019.01.015
Zhang, L., Ding, B., Chen, Q., Feng, Q., Lin, L., and Sun, J. (2017). Point-of-care-testing of nucleic acids by microfluidics. Trends Anal. Chem. 94, 106–116. doi: 10.1016/j.trac.2017.07.013
Zheng, Y.-Y., Ma, Y.-T., Zhang, J.-Y., and Xie, X. (2020). COVID-19 and the cardiovascular system. Nat. Rev. Cardiol. 17, 259–260. doi: 10.1038/s41569-020-0360-5
Keywords: POC biosensors, PDMS, paper, flexible materials, COVID-19
Citation: Choi JR (2020) Development of Point-of-Care Biosensors for COVID-19. Front. Chem. 8:517. doi: 10.3389/fchem.2020.00517
Received: 28 April 2020; Accepted: 19 May 2020;
Published: 27 May 2020.
Edited by:
Huan-Tsung Chang, National Taiwan University, TaiwanReviewed by:
Ninghao Zhu, Pennsylvania State University (PSU), United StatesWei Wen, Hubei University, China
Copyright © 2020 Choi. This is an open-access article distributed under the terms of the Creative Commons Attribution License (CC BY). The use, distribution or reproduction in other forums is permitted, provided the original author(s) and the copyright owner(s) are credited and that the original publication in this journal is cited, in accordance with accepted academic practice. No use, distribution or reproduction is permitted which does not comply with these terms.
*Correspondence: Jane Ru Choi, amFuZXJ1Y2hvaSYjeDAwMDQwO2dtYWlsLmNvbQ==; amFuZXJ1LmNob2kmI3gwMDA0MDt1YmMuY2E=